Bosch OBD 1350 User Manual Download | Manualshive

Page: 39 / 56

background image

580001 | REV. A | 11.2016

OBD 1350

ProGrade OBDII Scan Tool

| User guide |

39

|

en

Oil Light Reset

Cycle key, Turn engine off, Key

on
Press BACK to exit

Press ENTER to continue

3. Reset oil light.

•

Press

.

Oil Light Reset

Press ENTER to continue

Press ENTER to reset

BACK to exit

4. After the command is sent, the oil light should be

off.
•

Press

to return to the

Service Light Reset

Menu

.

Oil Light Reset

Press ENTER to continue

Command sent

5.15 Battery Reset

The Battery Reset function allows the scan tool to tell
the vehicle that the battery has been replaced. This
function will only appear on the Special Tests menu
when supported by the currently selected vehicle. Reset-
ting the battery system when a new battery is installed
allows the vehicle to customize charging to the age and
condition of the battery.

Battery Information

The vehicle may contain either a lead-acid battery or an
AGM (absorbed glass mat) battery. Leadacid batteries
contain liquid sulphuric acid and can spill when over-
turned. AGM batteries also contain sulphuric acid, but
the acid is contained in glass mats between the terminal
plates.
If the original battery is replaced with a different type of
battery (eg. a lead-acid battery is replaced with an AGM

battery) or a battery with a different capacity (mAh), the
vehicle may require reprogramming to the new battery
type in addition to performing the battery reset. Repro-
gramming is not a function of the tool. Consult the
vehicle manual for additional vehicle-specific informa-
tion.
From the

Battery/Charging Services Menu

:

1. Select

Battery Reset

.

•

Use the

UP

and

DOWN

keys until

Battery

Reset

is highlighted.

•

Press

.

Battery/Charging Services

Battery Reset

2. Follow the instructions displayed. They will vary

depending on the vehicle.
•

Press

.

Battery Reset

Required Whenever:

Battery has been replaced

Otherwise instructed by shop

manual

Press ENTER to continue

3. Perform

Battery Reset

.

•

The messages displayed during battery reset
will vary depending on the vehicle.

Battery Reset

Please Wait

(May Take 30 Secs)

Time remaining

0:28

4. Battery Reset Complete.

•

Press

to return to the

Battery/Charging

Services Menu

.

«
...
37
38
39
40
41
...
»

Summary of Contents for OBD 1350

























































Reviews:

No comments

Related manuals for OBD 1350

Brand: Panasonic Pages: 72

KW9M Eco-Power Meter

Brand: Panasonic Pages: 2

Brand: National Instruments Pages: 15

Brand: PAT Pages: 57

Brand: TA Instruments Pages: 7

Brand: Artesia Pages: 36

SoundTrack LxT N/Forcer

Brand: Larson Davis Pages: 12

Brand: Mark-10 Pages: 26

International 2S Pro

Brand: Brantz Pages: 2

Brand: Salutron Pages: 2

Brand: Hanna Instruments Pages: 28

Brand: Sagola Pages: 16

Brand: KEM Pages: 49

Brand: Ecodhome Pages: 12

Cerabar S PMC71

Brand: Endress+Hauser Pages: 48

Brand: Omega Pages: 4

Brand: Racelogic Pages: 15

Brand: wtw Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands