K2200 Series |
User Guide | 4.0
Key Administration/ Access Control
EN
| 19
Bosch Security Systems | 7/03 | 17376 v1.1 / 47491C
•
0101
0101
0101
Instead of voiding a key from the system,
consider changing its access code to 0
(zero). By doing this you will prevent use
of the key (any attempt will result in a No
Access: Locked Out transaction being
generated) but you will also have a record
of a 'lost' key being used unsuccessfully
To Void a Key:
1.
Present an editor key to the faceplate reader.
2.
Enter the password and press [ENT], if required.
3.
You will now see the CMD prompt.
4.
Type [V] and press [ENT].
CMD V_
5.
At the ID Prompt,
ID _
you can select the key to be deleted using one of
these methods:
-
If you are in possession of the key itself,
present the key to the faceplate reader.
If the key is not in the database, you
will get a message for about 2
seconds
NOT IN DATABASE
before returning to the ID prompt.
-
Type the 4-digit ID of the key and press
[ENT]. Any number between 1 and 4000
will be accepted.
-
If you are using 12-character IDs, you
can type the ID and press [ENT]. You
must type the name exactly as it was
originally entered. If no match is found,
you will get a message
UNKNOWN NAME
for about 2 seconds before returning
to the ID prompt.
6.
Whatever method you use to find a key, you will
be presented with the ID number and access
code.
ID 27 AC 7
7.
At this point, you can use the up and down
arrow keys to move through the database to find
the key you want to delete. You can also press
the FastFind (*) button to return to the ID
prompt.
WHO SMITH AB
8.
Once you have selected the key you want to
delete, press [ENT].
9.
At the
CONFIRM VOID
prompt,
CONFIRM VOID
press [
Y]
to confirm and you will be returned to
the
CMD
prompt. Any other key will return you
to the
CMD
prompt without voiding the key.
When a key has been voided, it will be rejected by
all the readers on the system and a
No Access: Unknown ID
transaction will be
produced. This will not be the case if:
•
Slave door controllers are disconnected or not
communicating with the master.
•
A download is in progress to a slave door
controller, in which case the new information
will not reach the slave until completion of the
download.
4.1.4
Editing Keys – The E Command
You can change the access code of a key as well as
the 12-character name (if used) at any time. You can
also assign a holiday profile to a keyholder. The
access code and holiday profile must already be
defined (see
Section 4.2.6 Access Codes – The AC
Command
and
Section 4.2.7 Holidays – The HR and HP
Commands
).
1.
Present an editor key to the faceplate reader.
2.
Enter the password and press [ENT], if required.
3.
You will now see the CMD prompt.
4.
Type [E] and press [ENT].
CMD E_
5.
At the
ID
prompt,
ID _
you can either use the up and down arrow keys
to select a key, or press the FastFind (*) button.
-
If you are in possession of the key itself,
present the key to the faceplate reader.
If the key is not in the database, you
will get a message for about 2
seconds
NOT IN DATABASE
before returning to the ID prompt.
-
Type the 4-digit ID of the key and press
[ENT]. Any number between 1 and 4000
will be accepted.
-
If you are using 12-character IDs, you
can type the ID and press [ENT]. You
must type the name exactly as it was
originally entered. If no match is found,
you will get a message
UNKNOWN NAME
for about 2 seconds before returning
to the ID prompt.
6.
Whatever method you use to find a key, you will
be presented with the ID number and access
code.
ID 27 AC 7
