Bosch GWH 345 ESR-L Manual Download | Manualshive

Page: 14 / 44

background image

6 720 607 909

14

Installation instructions

Fig. 14 Maximum vent and combustion air lengths

Vent material

The GWH-345/450-ESR requires 3 inch sealed single
wall stainless steel vent pipe (AL29-4C). Use of any
other vent material will void the manufactures warranty
and may result in a hazardous condition. For specific
questions concerning vent material, specifications,
usage or installation, contact the vent manufacturer
directly.

Contact your Bosch supplier for stocked vent material.

Vent Safety System

The GWH-345/450-ESR will shut down if inadequate
exhaust venting is detected or a lack of combustion air
is provided to the unit; see troubleshooting section on
page 34. Correct the problem and then reset the heater
before operating.

3.6.2

Vent connections and combustion air inlet
restrictors

Exhaust vent connection

B

Attach the flue gas exhaust accessory (8 705 504
142) to the top of the unit (position 1) using the 4
screws and gasket provided

B

Insert 3" single wall stainless steel vent pipe into
exhaust vent adapter 1.5" and tighten the clamp
(position 2).

Note:

Failure to fully insert and tighten vent pipe may

cause flue gas leakage or condensate damage that is
not covered under the manufacturer's warranty.

Fig. 15 Exhaust vent connection

Company

Contact information

Z-flex

www.z-flex.com
800-654-5600

ProTech
Industries

www.protechinfo.com
800-766-3473

Heat-Fab

www.heatfab.com
800-772-0739

Table 4 Vent manufacturer contact information

6720607909-14.3JS

Vent pipe

Combustion
air intake

Z flex

Protech

Heat Fab

3” Horizontal
terminator

TEE only

TEE only

9390 TEE

3” Vertical
terminator

2SVSRCF03

FSRC3

5300CI

90°
Condensate
drain Tee

2SVEVWCF03

FST3 &

FSDF3

93PLSTEE

Horizontal
Condensate
drain

2SVEDWCF03

FSHD03

9321

Condensate
Drain Tube

2SVEDTK

N/A

7000TUBE

Table 5 Approved vent termination and condensate

drain part numbers (subject to change)

«
...
12
13
14
15
16
...
»

Summary of Contents for GWH 345 ESR-L













































Reviews:

No comments

Related manuals for GWH 345 ESR-L

Brand: DAB Pages: 8

Brand: GEAppliances Pages: 72

Brand: Lasko Pages: 4

Brand: Rainfresh Pages: 10

Brand: Danfoss Pages: 8

Brand: Danner Pages: 2

Brand: salmson Pages: 49

Brand: Gabarron Pages: 8

Brand: KEKAI Pages: 12

Brand: TDRFORCE Pages: 12

Brand: Watson Marlow Pumps Pages: 95

Brand: Watson Marlow Pumps Pages: 87

Brand: Watson Marlow Pumps Pages: 127

Brand: ubbink Pages: 31

Brand: Annovi Reverberi Pages: 18

COBRA DS 0600 E

Brand: BUSCH Pages: 24

RJS-75SS Series

Brand: red lion Pages: 32

Brand: Eliz Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands