Bosch GWH 345 ESR-L Manual Download

Page: 32 / 44

6 720 607 909

Maintenance and service

Parameter storage

Keep pressing the reset button

for at least 2

seconds in order to record adjustments. The digital
display blinks with the symbol

Exiting Diagnostic mode

Press ON/OFF button to turn appliance OFF and
then back ON again.

Mode

Parameter

Values

Not used

---------- (displayed values have no relevance)

Not used

---------- (displayed values have no relevance)

Error code history

Displays the last 8 error codes. Use the hot water temperature selector
(right dial) to toggle from newest (left) to oldest (right) error codes.

Outlet water temperature

Displays the real-time outlet temperature as detected by the outlet
temperature sensor.

Selected outlet water
temperature

Displays the outlet water temperature as selected by the user during
normal operation.

DHW temperature (only if
12kOhm thermistor used)

Displays the real-time temperature of the DHW tank as detected by the
12kOhm external thermistor. (Display will show 32 if thermistor not
used)

Selected DHW temperature
(only if 12kOhm thermistor
used)

Displays the domestic hot water temperature as selected by the user (only if
12kOhm external thermistor used).

Not used

---------- (displayed values have no relevance)

Pressure switch

00 - Open pressure switch - fan is off or there is no exhaust gas flow

01 - Closed pressure switch - fan is on or there is exhaust gas flow

Temperature limiter

01 - temperature is below the limit (220°F)

E9 - temperature is above the limit (220°F)

Not used

---------- (displayed values have no relevance)

Gas valve

00 - gas valve closed

01 - gas valve open

Modulating gas valve
position (%)

00 - gas valve closed

01-70 - gas valve position min/max

Thermostat

00 - thermostat open

01 - thermostat closed

Fan

00 - fan off

01 - fan on

Ionization

00 - no flame detected

01 - flame detected

Not Used

---------- (displayed values have no relevance)

Not Used

---------- (displayed values have no relevance)

Not Used

---------- (displayed values have no relevance)

Not Used

---------- (displayed values have no relevance)

Digital display test

All LCD components appear

Temperature unit selection
(°C or °F)

Use the hot water temperature selection knob to select temperature
units °C or °F. (ccw for °C and cw for °F)

Table 16

Summary of Contents for GWH 345 ESR-L













































Search results

Summary of Contents for GWH 345 ESR-L

Reviews:

Related manuals for GWH 345 ESR-L

Brands by name

Popular brands

Bosch GWH 345 ESR-L, Manual

Search results

Summary of Contents for GWH 345 ESR-L

Reviews:

Related manuals for GWH 345 ESR-L

Brands by name

Popular brands