background image

6 720 607 909

Installation instructions

21

Fig. 23

*

For clearances not specified in ANSI Z223.1 / NFPA 54 or CSA -B149.1. “Clearances in accordance with local installation codes and 
the requirements of the gas supplier.”

Fixed

Closed

6720608836-18.1JF

Q

Ref.

Description

Direct Vent Terminal 

Clearances

Other than Direct Vent 

Terminal Clearances

Canadian 

Instalations

1)

US 

Instalations

2)

Canadian 

Instalations

1)

US 

Instalations

2)

M

Clearance to permanently closed window

*

*

*

*

Vertical clearance to ventilated soffit located 
above the terminal within a horizontal distance 
os 2 feet (61 cm) from the center line of the 
terminal

N/A

N/A

*

*

N

Clearance to each side of center line extended 
above meter/regulator assembly

3 feet (91 cm) 
within a height 
15 feet above 
the meter/regula-
tor assembly 

*

3 feet (91 cm) 
within a height 15 
feet above the 
meter/regulator 
assembly 

*

O

Clearance to a mechanical air supply inlet

6 feet (1.83 m)

3 feet (91 cm) 
above if within 
10 feet (3 m) 

6 feet (1.83 m)

3 feet (91 cm) 
above if within 
10 feet (3 m) 

P

Clearance above paved sidewalk or paved 
direway located on public property

7 feet (2.13 m)

3)

*

7 feet (2.13 m)

3)

7 feet (2.13 m)

Q

Clearance under veranda, porch, deck or 
balcony

12 inches 

(30cm)

4)

*

12 inches 

(30cm)

4)

*

Table 10Vent terminal clearances 

1)

In accordance with the current CSA B149.1 

Natural Gas and Propane Installation Code

.

2)

In accordance with the current ANSI Z223.1 / NFPA 54 

National Fuel Gas Code

3)

A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family dwellings and serves 
both dwellings.

4)

Permited only if veranda, porch, deck or balcony is fully open a minimum of two sides beneath the floor.

Summary of Contents for GWH 345 ESR-L













































Reviews: