Bosch GLM 120 C Professional, Original Instructions Manual

Page: 30 / 388

30 | English
1 609 92A 4F4 | (22.10.2018) Bosch Power Tools
Grade measurement/digital spirit level
Select the inclination measurement/digital spirit level .
The measuring tool automatically switches between two
states.
1° 2° 3°
The digital spirit level is used to check the hori-
zontal or vertical alignment of an object (e.g.
washing machine, refrigerator, etc.).
When the inclination exceeds 3°, the ball in the
display lights up red.
The bottom of the measuring tool is used as
the reference level for the digital spirit level.
88.0°
Grade measurement is used to measure a
slope or incline (e.g. of stairs, railings, when
fitting furniture, laying pipes, etc.).
The left-hand side of the measuring tool serves
as the reference level for grade measurement.
If the display flashes during measurement, the
measuring tool has been tipped too heavily to the side.
Memory functions
The value or end result of each completed measurement is
automatically saved.
Tip : When the camera is switched on, the photo is saved
automatically, together with the measuring result. The fol-
lowing information is printed on the photo:
– Measuring result
– Individual measurements (required to determine the
measuring result)
– Measuring function used
– Reference
– Date and time
– Tilt angle (only with spirit level switched on).
If the photo is intended to be used for documentation pur-
poses and transferred via micro USB cable, we recommend
disabling the zoom function.
When the measuring tool is connected to an end device by
micro USB cable, a csv file with all saved measured values is
additionally created.
Memory value display
A maximum of 50 values (measured values or photos with
measured values) can be retrieved.
Select the memory function using the soft key
(12) [ ] .
09.06.2017
13:20:23
30º
32.852 m
4 4
m 48.873
m 56.335
35.5 º
The number of the memory value is shown at
the top of the display, the corresponding
memory value and the corresponding measur-
ing function are shown at the bottom
Press the button
(4) [ + ] to browse forwards
through the saved values.
Press the button (11) [ – ] to browse backwards through the
saved values.
If there is no value available in the memory,
0.000 is shown
at the bottom of the display and 0 at the top.
The oldest value is located in position 1 in the memory, while
the newest value is in position 50 (when 50 memory values
are available). When a further value is saved, the oldest
value in the memory is always deleted.
Deleting the memory
To open the memory, press the soft key (12) [ ]. Then
press the soft key (3) [ ] as often as required to delete the
content of the memory. To delete all values stored in the
memory, the
function from the settings menu can also be
used. This is then confirmed by pressing the soft key (12)
[ ].
Formatting the memory
The USB memory can be reformatted (e.g. in the event of
storage problems). To do this, select the
function from
the settings menu and confirm this by pressing the soft key
(12) [ ]. Formatting deletes all data stored in the memory.
The USB memory must not be formatted using other
devices (e.g. external PC).
Adding/subtracting values
Measured values or end results can be added or subtracted.
Adding values
The following example describes the addition of areas: De-
termine an area as described in the section on area measure-
ment (see "Area measurement", page 28).
2
09.06.2017
13:20:23
0.0º
55.049 m 2
m
2
51.300
m 3.749
+
Press the button (4) [ + ]. The calculated area
and the + symbol will be displayed. Press the
measuring button (2) [ ] to start another area
measurement. Measure the area as described
in the section on area measurement (see "Area
measurement", page 28). Once the second
measurement is completed, the result of the second area
measurement is displayed below. To show the end result,
press the measuring button
(2) [ ] once more.
Note: In the case of a length measurement, the end result is
displayed immediately.
Subtracting values
To subtract values, press the button (11) [ – ]. The sub-
sequent steps are the same as for the section on adding val-
ues.
Deleting measured values
Briefly pressing the on/off/delete button (9) [ ] will delete
the last measured value in all measuring functions.
Bluetooth®
interface
Transmitting data to other devices
The measuring tool is fitted with a Bluetooth® module which
enables wireless data transfer to certain mobile devices with
a
Bluetooth® interface (e.g. smartphone, tablet).
Information about the system requirements for a Bluetooth®
connection can be found on the Bosch website at
www.bosch‑pt.com
u
Further information can be found on the Bosch
product page.
When transmitting data by means of Bluetooth® , time lags
may occur between the mobile device and the measuring
tool. This can be due to the distance between the two
devices or the measurement object itself.