Bosch C1050ES Installation Manual Download Page 26 | Manualshive

Page: 26 / 72

background image

6 720 646 812

26

Installation instructions

Fig. 27 Leveling wall mounting bracket

Fig. 28 Mounting the heater

3.8

Gas piping & connections

Before  connecting  the  gas  supply,  check  the  rating
plate on the right side of the heater to be sure that the
heater  is  rated  for  the  same  gas  to  which  it  will  be
connected.
In the United States: The installation must conform with
local  codes  or,  in  the  absence  of  local  codes,  the
National Fuel Gas Code ANSI Z223.1/NFPA 54.
In Canada: The Installation must conform to CGA B149
INSTALLATION  CODES  and/or  local  installation
codes.

GAS CONNECTIONS

B

Install a manual gas shut off valve on the gas supply
line within easy reach of the appliance.

B

Install a union when connecting gas supply.

B

The minimum internal diameter required for
any appliance connector is ¾”, see

Fig. 31

for

more details on pipe sizing.

B

Undersized flexible appliance connector not permit-
ted.

B

National Fuel Gas Code requires that a sediment
trap (drip leg) be installed on gas appliances not so
equipped. The drip leg must be accessible and not
subject to freezing conditions. Install in accordance
with the recommendations of the serving gas
supplier, see Fig. 2.

Warning:

Appliance must be installed

vertically.

6720608158-64.1AL

6720608158-05.1AL

6720608158-05.1AL

Warning:

DO NOT connect to an

unregulated or high pressure propane
line or to a high pressure commercial
natural gas line.

Warning:

The heater must be isolated

from  the  gas  supply  piping  system
during  any  pressure  testing  of  that
system  at  test  pressures  equal  to  or
more than 0.5 psig. If overpressure has
occurred,  such  as  through  improper
testing of the gas lines or malfunction of
the  supply  system,  the  gas  valve  must
be checked for safe operation.

«
...
24
25
26
27
28
...
»

Summary of Contents for C1050ES









































































Reviews:

No comments

Related manuals for C1050ES

Brand: Canon Pages: 12

Brand: A&D Pages: 35

Brand: Harken Hoister Pages: 12

Brand: Wallenstein Pages: 48

Brand: Oki Pages: 2

Brand: Oki Pages: 32

XMODS Custom RC

Brand: Radio Shack Pages: 4

Brand: Roav Pages: 10

Brand: SUP’AIR Pages: 29

Powerbridge TSV

Brand: Fishman Pages: 2

Brand: Prorack Pages: 14

Brand: Temposonics Pages: 25

FT2A-PWR-IT Series

Brand: Crestron Pages: 2

Brand: Crivit Pages: 70

37-Key Audio/MIDI Interface and Controller Ozonic

Brand: M-Audio Pages: 38

Brand: Metra Electronics Pages: 8

SYSVRF JOINT OUT 02 HP

Brand: SystemAir Pages: 2

Pro-Line ConstantON 80756LO

Brand: GE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands