Bosch C1050ES Installation Manual Download Page 40

Page: 40 / 72

6 720 646 812

Operation instructions

5.8

Program button

Fig. 63 “Program” key

5.8.1

Memorizing selected temperature

Press buttons

to select desired

temperature.

Hold “Program” button for 3 seconds to save
temperature.

When LCD stops blinking, temperature is saved in
memory.

Using “Program” function

In order to select memorized temperature

Press “Program” key.

LCD shows pre-memorized temperature, which is now
the hot water selected temperature.

5.9

Locked condition

This condition is only valid for appliances with one or
more remote controls installed.

Fig. 64 Locked condition

Whenever LCD shows

the temperature setting

cannot be adjusted because the appliance is in use by
a user which already selected a different temperature.
Appliance will be automatically unlock 5 minutes after
closing hot water tap.

Summary of Contents for C1050ES









































































Search results

Summary of Contents for C1050ES

Reviews:

Related manuals for C1050ES

Brands by name

Popular brands

Bosch C1050ES, Installation Manual

Search results

Summary of Contents for C1050ES

Reviews:

Related manuals for C1050ES

Brands by name

Popular brands