Bosch C1050ES Installation Manual Download Page 19

Page: 19 / 72

6 720 646 812

Installation instructions

Backdraft reducer

The Heat Fab backdraft reducer (9301BFP) is the pre-
ferred option for limiting backdraft (see Fig. 20).

Note: The following solution is available only for
3" diameter venting.

Fig. 20 Part nr 9301BFP

Installation

For this solution to be effective, the internal flapper must
be 100% closed when the water heater is not running.
Refer to Figures 22 and 23 for preferred installation
positions in the vent system.

Installation considerations:

• Install damper per the supplied manufacturer‘s

instructions.

• The damper is only to be used in the exhaust vent

piping.

• Ensure directional arrow on damper label faces in the

same direction as exhaust flow.

• If installed horizontally, the axis must be horizontal or

slightly pitched up towards termination to ensure
damper closes 100% when heater is not running.

• To allow accessibility, damper must not be installed

in an enclosed section of vent pipe.

• Do not install damper in unconditioned spaces (e.g.

attics) Condensation can build up while the heater is
running which can later freeze and potentially block
the flapper.

Fig. 21 Blackflow reducer (9301BFP) installed

Fig. 22

Fig. 23

6720608643-18.1V

6720608643-19.1V

6720608542-06.2V

Preferred damper position for vertical terminations

Unconditioned
space. Do not
install damper.

Enclosed vent
pipe. Do not
install damper.

6720608836-30.2V

Summary of Contents for C1050ES









































































Search results

Summary of Contents for C1050ES

Reviews:

Related manuals for C1050ES

Brands by name

Popular brands

Bosch C1050ES, Installation Manual

Search results

Summary of Contents for C1050ES

Reviews:

Related manuals for C1050ES

Brands by name

Popular brands