manualshive.com logo in svg

Bosch BSS250-21-2, Installation And User Manual

Share
Download
Bosch BSS250-21-2 Installation And User Manual Download Page 50

50 

 

ELECTRIC BOOSTING 
  

Water stored in the storage tank is heated automatically by an electric booster heating unit.  

The booster element heats the water during very cloudy or rainy weather, during the winter 

months, or during periods of unusually high demand, such as when friends or relatives visit.  

The booster heating unit is controlled by an electric thermostat.  The thermostat and heating 

element are mounted on the solar storage tank inside the two covers.  The boost water 

temperature is automatically controlled to the thermostat setting when the booster heating unit 

is energised. 

The thermostat is tradesperson adjustable.  It has a minimum temperature setting of 60ºC and 

a recommended maximum temperature setting of 75ºC.  It can only be adjusted by an 

authorised person.  Automatic safety controls are fitted to the water heater to provide safe and 

efficient operation. Bosch recommends that the thermostat be set at 75 ºC for the best 

efficiency. 

GAS BOOSTING 

 

Where gas boosting in used the electric element and thermostat of the tank are not connected 

to power. The gas booster is installed and connected inline between your solar tank and the 

hot water outlets of your home. The water from the outlet of the tank passes through the 

booster, if the sensor inside the gas booster detects the water temperature is lower than the 

preset temperature of the booster, the booster will turn on and heat the water. 

 

 
 
 

 
 
 
 
 
 
 

Summary of Contents for BSS250-21-2





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands