Bosch BSS250-21-2 Installation And User Manual Download Page 1

Page: 1 / 52

19/07/2011

Version 19

Solar Wizard

MODELS

BSS250E-2 / BSS250-21-2 / BSS250-26-2
BSS300E-2 / BSS300-21-2 / BSS300-26-2
BSS400E-2 / BSS400-21-2 / BSS400-26-2

Australia & New Zealand

INSTALLATION AND USER

HANDBOOK



System Installation



Controller & Pump



Solar Panels



Gas solar booster



Solar Tank

This solar hot water system must be installed in accordance with the manufacturer’s installation
instructions, AS5601, AS3500.4. AS3000 wiring regulations (in New Zealand NZBC G12) and all Local
Building, Water and Gas fitting regulations.

To be installed and serviced only by an authorised person

This appliance is not suitable for use as a pool heater

Please see important note regarding tank on Page 15

The “authorised installing person” is responsible for:
1.

Correct commissioning of this system.

Ensure units perform to the specifications stated on the rating label.

3..

Demonstrate operation of the system to the customer before leaving.

Hand these instructions to customer.

Failure to install this system in accordance with these installation instructions may void warranty

Note: These instructions are subject to change, due to continuous product improvement.

Summary of Contents for BSS250-21-2





















































Search results

Summary of Contents for BSS250-21-2

Reviews:

Brands by name

Popular brands

Bosch BSS250-21-2, Installation And User Manual

Search results

Summary of Contents for BSS250-21-2

Reviews:

Brands by name

Popular brands