Bosch AUTODOME IP 4000i Installation Manual Download

Page: 11 / 44

AUTODOME IP 4000i

Mounting Accessories | en

Bosch Security Systems

Installation Manual

2017.08 | 1.0 | F.01U.xxx.xxx

Mounting Accessories

Model Number

Description

Installation Location

NDA-U-WMT

Pendant wall mount

Indoor walls (direct installation)
Outdoor walls (onto NDA-U-PAx or
NDA-U-WMP)

NDA-U-PA0
NDA-U-PA1
NDA-U-PA2

Surveillance cabinet
(24VAC, 120VAC, or 230VAC)

Indoor/outdoor walls

NDA-U-CMT

Corner mount adapter

Corner of a building

NDA-U-PMAL

Pole mount adapter (large)

Poles that support surveillance
cameras

NDA-U-WMP

Mount plate for wall mount, corner
mount, or pole mount

Indoor/outdoor walls

NDA-4020-PIP

Pendant interface plate to mount
camera to NDA-U-WMT or to NDA-
U-PMT

Between camera and wall mount or
pipe mount

NEZ-A4-SMB

Surface mount box

Indoor hard-ceilings

NDA-U-PSMB

Surface mount box (SMB) for wall
mount or pipe mount

Indoor walls

NDA-U-PMT

Pendant pipe mount

Indoor high ceilings

NDA-U-PMTE

Pendant pipe mount extension

Indoor high ceilings

VGA-IC-SP

In-ceiling support kit

Indoor suspended ceilings

NDA-4020-PLEN

Plenum box

Plenum spaces in indoor
suspended ceilings

Summary of Contents for AUTODOME IP 4000i













































Search results

Summary of Contents for AUTODOME IP 4000i

Reviews:

Related manuals for AUTODOME IP 4000i

Brands by name

Popular brands

Bosch AUTODOME IP 4000i, Installation Manual

Search results

Summary of Contents for AUTODOME IP 4000i

Reviews:

Related manuals for AUTODOME IP 4000i

Brands by name

Popular brands