Bosch AUTODOME IP 4000i Installation Manual Download

Page: 39 / 44

AUTODOME IP 4000i

Connection | en

Bosch Security Systems

Installation Manual

2017.08 | 1.0 | F.01U.xxx.xxx

Connection

Caution!

Compliance with EN50130-4 Alarm Standard – CCTV for Security Applications
To meet the requirements of the EN50130-4 Alarm Standard, an ancillary uninterruptable
power (UPS) supply is necessary. The UPS must have a

Transfer Time

between 2–6 ms and a

Backup Runtime

of greater than 5 seconds for the power level as specified on the product

datasheet.

Note

: Consult the National Electrical Code (NEC) for cable bundling requirements and

limitations.

Connect the cable to the 24 VAC wires from the camera.

Label ID

Description

Cable Wire Color

AC24V

24 VAC

Red

AC24V

24 VAC

Black

EARTH

Earth Ground

Yellow/Green

Connect the Ethernet cable to the RJ45 connector of the camera. The following figure
illustrates a typical system configuration.

Figure 14.1: AUTODOME IP System Config

1 AUTODOME camera

2 IP connection (Ethernet/CAT5/CAT6) (100 m maximum)

3 Network switch

4 Network device (computer with monitor, DVR/NVR, etc.)

If desired, connect the alarm and/or audio wires as identified in the following table.

Label ID

Description

Cable Wire Color

ALARM_COM

Alarm Communications Red

ALARM_OUT

Alarm Out

Brown

Summary of Contents for AUTODOME IP 4000i













































Search results

Summary of Contents for AUTODOME IP 4000i

Reviews:

Related manuals for AUTODOME IP 4000i

Brands by name

Popular brands

Bosch AUTODOME IP 4000i, Installation Manual

Search results

Summary of Contents for AUTODOME IP 4000i

Reviews:

Related manuals for AUTODOME IP 4000i

Brands by name

Popular brands