Bosch APC-AMC2-4W Installation Manual Download Page 11

Page: 11 / 60

AMC2 4W

Safety Instructions | en

Bosch Security Systems

Installation manual

F.01U.024.965 | V.4 | 2006.09

2.3

Safety Precautions

Read instructions!

Before working with the AMC2 4W, read these instructions

carefully. Make sure you have understood all information

described in this document.

Warning! Risk of electric shock!

External power supplies must be installed and put into service

by qualified personnel. Compliance with the relevant regula-

tions must be ensured.

Warning! Risk of damaging equipment!

•

Always switch off power of the AMC2 4W before mod-

ifying the installation.

•

Do not connect or disconnect plug connectors, data

cables or screw connectors while power is on!

Health and Safety

Installation of the AMC2 4W must comply with any local fire,

health and safety regulations. A secured door that may be part

of an escape route from an area must be installed with:

•

A fail-safe lock. So that the door will be released if

power fails. Ideally, a magnetic lock should be used as

these are less likely to jam or seize.

•

A normally-closed break-glass or manual pull in the

lock supply wiring, so that in an emergency the fail-

safe lock can be immediately powered down.

Summary of Contents for APC-AMC2-4W





























































Search results

Summary of Contents for APC-AMC2-4W

Reviews:

Related manuals for APC-AMC2-4W

Brands by name

Popular brands

Bosch APC-AMC2-4W, Installation Manual

Search results

Summary of Contents for APC-AMC2-4W

Reviews:

Related manuals for APC-AMC2-4W

Brands by name

Popular brands