Bosch 0 275 007 511, Original Instructions Manual, Page: 37 / 193

English–
10
Bosch eBike Systems 0 276 001 SPN | (17.7.14)
Power Supply of External Devices via USB
Connection
With the USB connection, it is possible to operate and charge
most devices whose power supply is possible via USB (e.g.,
various mobile phones).
Prerequisite for charging is that the on-board computer and a
sufficiently charged battery pack are inserted in the eBike.
Open the protective cap
9
of the USB port on the on-board
computer. Connect the USB connection of the external device
to the USB port
8
on the on-board computer using a standard-
compliant Micro A/Micro B USB 2.0 cable. Using a USB cable
that is not standard-compliant or a cable/adapter combina-
tion can lead to damage to the on-board computer.
Attention:
Users connected to Nyon can affect the range of
the eBike.
Notes on Riding with the eBike System
When does the eBike Drive Unit Operate?
The eBike drive unit assists you when riding, as long as you
step into the pedals. Without pedaling, there is no assistance.
The motor output always depends on the amount of your ped-
aling power.
When applying less pedaling power, the assistance or support
will be lower than when applying a lot of pedaling power. This
applies independent of the assistance Level.
The eBike drive automatically switches off at speeds in excess
of 25/45 km/h. When the speed falls below 25/45 km/h, the
drive is automatically available again.
An exception applies to the push/start aid feature, in which
the eBike can be pushed at low speed without pedalling. The
pedals may also rotate when the push aid is used.
The eBike can also be ridden as a normal bicycle without as-
sistance at any time, by either switching off the eBike system
or setting the assistance level to
“OFF”
. The same applies
when the battery pack is empty.
Interaction of the eBike System with the Bicycle Gears
The bicycle gears should be used as with a normal bicycle,
even with eBike motor assistance (please observe the operat-
ing instructions of your eBike).
Independent of the type of gearing, it is recommended to
briefly interrupt the pedaling while changing gears. This
makes changing gears easier and reduces the wear of the
drive train.
By selecting the right gear, you can increase the speed and
range with the same pedaling effort.
602 Internal battery pack error while
charging Unplug the charger from the battery pack. Restart the eBike system. Plug
the charger into the battery pack. If the problem persists, contact your
Bosch eBike dealer.
602 Internal battery pack error Restart the system. If the problem persists, contact your Bosch eBike
dealer.
603 Internal battery pack error Restart the system. If the problem persists, contact your Bosch eBike
dealer.
605 Battery pack temperature error The eBike is outside of the permissible temperature range. Switch off the
eBike system and allow the drive unit to either cool down or heat up to the
permissible temperature. Restart the system. If the problem persists,
contact your Bosch eBike dealer.
605 Battery pack temperature error while
charging Unplug the charger from the battery pack. Allow the battery pack to cool.
If the problem persists, contact your Bosch eBike dealer.
606 External battery pack error Check the wiring. Restart the system. If the problem persists, contact
your Bosch eBike dealer.
610 Battery pack voltage error Restart the system. If the problem persists, contact your Bosch eBike
dealer.
620 Charging error Replace the charger. Contact your Bosch eBike dealer.
640 Internal battery pack error Restart the system. If the problem persists, contact your Bosch eBike
dealer.
655 Multiple battery pack errors Switch off the eBike system. Remove the battery pack and reinsert it. Re-
start the system. If the problem persists, contact your Bosch eBike dealer.
656 Software version error Contact your Bosch eBike dealer so that he can perform a software
update.
No display Internal error of the on-board computer Restart your eBike system by switching it off and back on.
Code Cause Corrective Measure