bora CKCB Installation Instructions Manual Download Page 7

EN

7

Safety

www.bora.com

2.2.2  Safety instructions – cooktop 

extractor installation

 DANGER!

Risk of poisoning caused by 

combustion gases!

When the cooktop extractor is used 

in exhaust mode, it draws in air from 

the room it is installed in and from 

neighbouring rooms. Without sufficient 

air, there will be a drop in air pressure. 

Toxic gases could be drawn out of the 

chimney or extraction ducting on a 

fireplace that depends on the room air 

and back into the room.

X

X

Make sure that there is always a 

sufficient air supply.

X

X

Only use reliable, tried-and-tested 

switching devices, (e.g. window 

contact switch, low pressure 

warning device) and have them 

approved by a qualified expert 

(certified chimney sweep).

 DANGER!

Risk of electric shock!

The control unit can contain residual 

charge and cause an electric shock.

X

X

Do not touch exposed contacts on 

the control unit.

 DANGER!

Risk of electric shock!

Incorrect stripping of the connection 

cable to external switching devices 

results in a risk of electric shock.

X

X

Ensure that the connection cable is 

secured with the strain relief clamp 

within the universal control unit.

X

X

Ensure that the stated stripping 

lengths are adhered to.

 DANGER!

Risk of electric shock and damage to 

property!

A damaged operating unit can lead to a 

short circuit.

X

X

Do not operate any appliance with a 

damaged operating unit.

X

X

Inform a BORA Service technician 

and have the operating unit 

replaced.

2.2.1  Safety instructions – cooktop 

installation

 DANGER!

Risk of electric shock!

Connecting the appliance to the mains 

incorrectly poses a risk of electric 

shock.

X

X

Make sure that the appliance has a 

fixed connection to the mains 

voltage.

X

X

Make sure that the appliance is 

connected to a properly installed 

protective conductor system.

X

X

Make sure that technical equipment 

is provided to enable all of the 

appliance’s poles to be disconnected 

from the mains with a contact 

opening width of at least 3 mm (LS 

switch and automatic circuit 

breakers, fuses, contactor).

 DANGER!

Risk of electric shock!

The connection cable can be damaged 

if it comes into contact with hot 

cooking zones. A damaged connection 

cable can cause a (fatal) electrical 

shock.

X

X

Make sure that the connection cable 

does not come into contact with hot 

cooking surfaces.

X

X

Make sure that the connection cable 

does not become trapped or 

damaged.

 CAUTION!

Lifting heavy loads can cause back 

injuries!

If not handled correctly, removing and 

installing the appliance can cause 

injuries to the limbs or torso.

X

X

Removing the cooktop from the 

packaging is a two-person job.

X

X

Placing the cooktop into the worktop 

cut-out is a two-person job.

X

X

Use appropriate aids to prevent 

damage or injuries to limbs or torso.

Summary of Contents for CKCB





































Reviews: