Bongshin BS-3520 Instruction Manual Download Page 28

Page: 28 / 66

HOLD

ZERO

DIGITAL INDICATOR

-3520

LOW

HIGH

HOLD

ZERO

DIGITAL INDICATOR

-3520

LOW

HIGH

Item Display

Setting Value

Contents of Setting

Automatic Zero Point Mode

It is a function to execute automatic
zero upon power input (Power On).

nonE : None

Auto : Automatic Zero Point

Analog Output (DAC)

Analog Output Mode

Analog output mode shall be
selected.

Warning: Analog output minute
calibration shall be conducted again
in case of changing output mode.

10V :

0 ~ 10V output

±5V :

-5V ~ +5V output

±10V : -10V ~ +10V output

4~20mA :

4 ~ 20mA output

0~20mA :

0 ~ 20mA output

5V :

0 ~ 5V output

Analog Lo Output

000.000

Setting Range

-199999 ~ 999999

In case analog output is 0V/ 0mA/
4mA, display value shall be set.

Analog output is conducted by force
while digit is flickering. (in case only
one digit is flickering)

Analog High Output

010.000 :

Setting Range

-199999 ~ 999999

In case analog output is 5V/ 10V/
20mA, display value shall be set.

Analog output is conducted by force
while digit is flickering (in case only
one digit is flickering)

Analog Lo Output Minute Calibration

0000 :

Setting Range

-9999 ~ 9999

In case it is 0V/ 0mA/4mA, minute
calibration of analog output shall be
conducted with the change in setting
value.
Value is increase by 10 while pushing

key.

It decreased by 10 while pushing

Key.

Initial

Value

Summary of Contents for BS-3520



































































Search results

Summary of Contents for BS-3520

Reviews:

Brands by name

Popular brands

Bongshin BS-3520, Instruction Manual

Search results

Summary of Contents for BS-3520

Reviews:

Brands by name

Popular brands