BONFIGLIOLI DGM User Instructions Download Page 149

Page: 149 / 173

Dei nst al l ati on and di sposa l

User instructions. DGM speed regulator

149

7. Deinstallation and disposal

This chapter contains:



a description of the deinstallation of the speed regulator



instructions for proper disposal

7.1 Deinstalling the speed regulator

HAZARD

Risk of fatal injury due to electric shock!

Fatal or serious injuries!

Disconnect the electrical voltage from the device and secure it to prevent it from being
reconnected.

Risk of electric shock and electric discharge. After shut-off, wait two minutes
(time for capacitor discharge)

Remove the cover of the speed regulator.

Disconnect the cables from the terminals.

Remove all the cables.

Remove the connection screws between the speed regulator/adapter plate.

Remove the speed regulator.

7.2 Instructions for proper disposal

Dispose of the speed regulator, packaging and the replaced components in accordance with the
provisions of the country where the speed regulator is installed.
The speed regulator must not be disposed of with normal household waste.

Summary of Contents for DGM














































































































































































Search results

Summary of Contents for DGM

Reviews:

Related manuals for DGM

Brands by name

Popular brands

BONFIGLIOLI DGM, User Instructions

Search results

Summary of Contents for DGM

Reviews:

Related manuals for DGM

Brands by name

Popular brands