background image

 

3. No communication over the RS-485 interface 

Flashes once per second 

4. Self-diagnostic mode 

Flashes five times per second 

5. Updating software or program memory failure 

Flashes twice per second 

1.4.4.1  While  operating,  the  module  monitors  the  voltage  at  its  power  inputs  and, 

depending  on the given value of 

Both Power Inputs Monitoring

  parameter  (see 

Clause 1.4.6), automatically detects a failure. 

 

Setting 

Both Power Inputs Monitoring

 on means that the power voltage should be applied 

to both power inputs; and the module enters the Power Failure mode if the power voltage is 
out of the normal range at any power input.  In  this  case  the  module  generates  one  Power 
Failure  message  for this power input (1  or  2)  and another Power Failure message for the 
module  itself  (input number  = 0). READY  indicator  shall  flash  with  low  duty  cycle  ratio.  The 
module will return to the quiescent mode when the power is restored on the both inputs, and 
after that the module transmits the Power Restored message over the RS-485 interface bus. 
If, otherwise, 

Both Power Inputs Monitoring

 is set off, the power voltage can be applied to 

any of the power inputs.  The module enters the Power Failure mode only in case of power 
failure at both power inputs and returns to the quiescent mode when the voltage is restored at 
any of them.  The events Power Failure and Power Restored are generated only for the 
module itself (input number = 0). 

1.4.4.2  If data are not communicated over the RS-485 interface within 1 s, the READY 

indicator begins flashing once per second (provided that the power voltage is in norm). When 
communication is restored the indicator is lit steady. 

1.4.5  Statuses of relays are displayed by indicators 1 to 4. When a relay is switched off 

(that is, normally closed contacts NC and COM are closed while normally open contacts NO 
and COM are open), the relevant indicator is off too. When the relay is switched on (that is, 
normally closed contacts NC and COM are open while normally open contacts NO and COM 
are closed), the relevant indicator is on. 

1.4.6  To  be  adjusted  for  specific  operation  requirements,  the  module supports 

programming the following parameters stored in its non-volatile memory: 

Parameter 

Description 

Value 

Range 

Factory Value 

1. Initial 

Condition 

The executive program, 
executed automatically after 
powering on (or resetting) the 
module and on receiving a 
Return to Initial Condition 
command 

1

 (On), 

2

 (Off), 

9

 (Lamp), 

10

 (Alarm 

Output) 

relay 1

 

relay 2

 

relay 3

 

relay 4

 

(Off) 

(Off) 

(Off) 

(Off) 

2. Activation 

Time 

The time during which the 
relay is active, for the 
commands which imply a 
limited activation time, if this 
time is not received in the 
command explicitly 

0…255

 

s

 

relay 1

 

relay 2

 

relay 3

 

relay 4

 

60 s 

60 s 

60 s 

60 s 

Summary of Contents for S2000-SP1 ORION ISS











Reviews: