background image

4

1.  GENERAL POINTS

Thank you for choosing the BODET Netsilon time server. This product has been carefully designed for your 

satisfaction according to the rules of our ISO9001 and ISO14001 quality system.
We recommend that you read this manual carefully before using the product for the first time.
Failure to observe these instructions may cause irreversible damage and invalidate the warranty. BODET shall not 

be responsible for any damage arising due to non-observance of these instructions.
Non-contractual data. Bodet reserves the right to make changes to equipment, including functional, technical and 

aesthetic changes, without notice.
This manual is subject to change without notice. To obtain the most recent version of this document, please refer to 

our website: www.bodet-time.com. 

1.1 Introduction

Observe all safety precautions during installation, operation and maintenance of this device. 
Key to symbols:

:  indicates advice, a recommendation or any other noteworthy information relating to use of Netsilon.

: indicates that special attention needs to be paid.

:  indicates that misuse or failure to follow the instructions could result in a electrical danger. This information 

must be taken into account when installing or using Netsilon.

4 versions are available for each Netsilon time server model, depending on the power supply:

 > 

Netsilon 7 / 9 / 11  AC

 

Netsilon 7 / 9 / 11 DC

 

Netsilon 7 / 9 / 11 AC+DC

 

Netsilon 7 / 9 / 11 AC+AC 

1.2 

General specifications

1.2.1.  Mechanical characteristics

Construction

Metal case - 1 U rack - 19”

Operating temperature

0°C to +50°C

Relative Humidity level at 40°C

0-90% RH without condensation

Protection class

IP20

Weight

2.5 kg

Dimensions

442 x 264 x 44.2mm

1.2.2.  Electrical characteristics

Power supply

AC :  100-240V  / 50-60Hz / 1.9-0.8A

DC : 22-30V  / 3.2-1.9 A

AC+DC   Redundant power supplies,

AC+AC   characteristics, above.

Alarm Input

Alarm IN  

Dry contact Input, potential-free contact  

I

IN 

≤ 10 mA

Alarm Output

Alarm OUT 

Relay NC-NO-C. 

Maximum current : 1A/50V , 1A/30V  

MTBF

100,000 hours

Summary of Contents for 907 900

















Reviews: