background image

!

Specifications for ProScope Mobile

Compatible Host Devices

Apple iOS devices including iPhone, iPad, and iPod touch

Image sensor

1/4 inch 5Mp Color CMOS

Resolution

320x240 (QVGA) / 640x480 (VGA)

Capture

Still image capture by Application

White Balance

MWB

Gain

AGC

Frame Rate

QVGA about 15fps (It changes with radio wave environment and the use device.)

Camera button Functions

a) Still image capture

b) Push W/B after still image captured

c) QVGA/VGA exchange

d) Initialize for factory settings

(Maintained after power supply is switched OFF)

Indicator LED

ON: The image is being transmitted

OFF: Power OFF or Battery is low

Flash 0.5sec: The W/B is being changed

Flash 1sec: The resolution is being changed

Flash 2sec: Initialize for factory settings

Light Switch

A-OFF-B (depends on the attached lens)

A: OFF, or reflective LEDs

OFF:OFF

B: Reflective LEDs, or Non Reflective LEDs

Power Switch

ON/OFF Slide switch

Magnification

X50 (when standard lens is used) Approximate magnification when displayed on 14-inch 

monitor.

Support Protocol

Wi-Fi  IEEE802.11b 

Camera Operational Range

about 10m from a Wi-Fi connected device

Access Format

ad hoc mode

Antenna

Internal Chip Multilayer antenna

Frequency

2.4GHz band width

SSID

AirMicroNNN

IP Address

192.168.NNN.1

Camera Screw

1/4-20 UNC

Battery

AA(Alkaline,Ni-MH)x3

Power Consumption

about 2.5W with standard lens

Continuous Operation time

Alkaline: about 2 hours, Ni-MH about 3 hours with standard lens.  

(Depends on environment)

Lens Mount

Standard ProScope Mount

Supply Current: A and B about 5V 120mA

Operation Temp

0ûC~40ûC

Storage Temp

-10ûC~60ûC

Outside Dimensions

153mm(H)x46mm(W)x43mm(D) (without Lens)

Weight

130g (without battery, with Lens)

Patented Technology

US Patent 5,442,489

Regulatory Compliance

FCC, CE Compliant

*

Specifications subject to change without notice.

6 0 7 7 A   S W   L a k e v i e w   B l v d .

L a k e   O s w e g o ,   O R   9 7 0 3 5

w w w . b o d e l i n . c o m

s u p p o r t @ b o d e l i n . c o m

8 0 0 - 4 4 1 - 6 8 7 7

**Important: The ProScope Mobile only works on Apple iOS devices including iPhone, iPad 

and iPod touch. This device DOES NOT WORK with Mac or PC computers.

12

Science Services GmbH
Unterhachinger Str. 75
81737 Munich, Germany
Tel: +49 (0)89 18 93 668 0 

 Fax: +49 (0)89 18 93 668 29

Mail: [email protected] 

 Web: ScienceServices.de

Your Partner for Microscopy and Lab Supplies

Summary of Contents for ProScope Mobile













Reviews: