P/N 033000=13610 Rev. 01-02-06 BMB Home Security
22
1. To access the menu, press the menu UP?
or menu DOWN?
button. The display now shows
ENTER PIN
.
2. Enter your 4-digit PIN code (factory setting 0000). For every digit entered, a * will appear.
3. When the PIN code has been entered correctly, the word
INSTALL
will show up on the display.
4. Use the menu buttons UP/DOWN ?
to go to menu item
5. NEW PIN
. Press OK to select this menu item. You can
also go to this menu item directly by pressing a 5 on the number pad.
5. Enter your new PIN code (4 digits). The new PIN can be seen on the display. Check if you entered the correct
PIN code and press OK.
6. Press CLEAR again to quit the menu. To confirm your choice, press 1 for Yes or 2 for No. If you choose Yes,
you will quit the menu. If you choose No, you go back to the first menu item.
9. Advanced security functions
9.1 Disarming the siren for silent alarm
You can set the security system to raise the alarm without sounding the siren (just the telephone dialler and
lighting). In case of a burglary, the built-in siren will not be activated (Note: other sirens installed will still work).
The siren is turned on in the factory settings.
1. To access the menu, press the menu UP?
or menu DOWN?
button. The display now shows
ENTER PIN
.
2. Enter your 4-digit PIN code (factory setting 0000). For every digit entered, a * will appear.
3. When the PIN code has been entered correctly, the word
INSTALL
will show up on the display.
4. Use the menu buttons UP/DOWN ?
to go to menu item
7. OPTIONS
. Press OK to select this menu item. You can
also go to this menu item directly by pressing a 7 on the number pad.
5. Use the menu buttons UP/DOWN?
to go to menu item
SIREN.
Press OK to select this menu item.
6. Choose 1 for
SIREN ON
or 2 for
SIREN OFF
.
7. Press CLEAR again to quit the menu. To confirm your choice, press 1 for Yes or 2 for No. If you choose Yes,
you will quit the menu. If you choose No, you go back to the first menu item.
9.2 Activating the chime
9.2.1 Built in Chime
The console can, when in DISARMED mode, sound a chime –ding-dong– when a door armed with a
Door/Window Sensor is opened. This ensures that you will always hear if someone is entering your house or
small children open a door. This function is activated in the factory settings.
1. To access the menu, press the menu UP?
or menu DOWN?
button. The display now shows
ENTER PIN
.
2. Enter your 4-digit PIN code (factory setting 0000). For every digit entered, a * will appear.
3. When the PIN code has been entered correctly, the word
INSTALL
will show up on the display.
4. Use the menu buttons UP/DOWN ?
to go to menu item
7. OPTIONS
. Press OK to select this menu item. You can
also go to this menu item directly by pressing a 7 on the number pad.
5. Use the menu buttons UP/DOWN ?
to go to menu item
CHIME
. Press OK to select this menu item.
6. Choose 1 for
CHIME ON
or 2 for
CHIME OFF
.
7. Press CLEAR again to quit the menu. To confirm your choice, press 1 for Yes or 2 for No. If you choose Yes,
you will quit the menu. If you choose No, you go back to the first menu item. .
8. If you see a note ? on the display, the chime is activated.
The chime function also works for the wired inputs on zones 31 and 32.
9.2.2 SH10 Remote Chime
The separate available SH10 Security Horn / Remote Chime will respond to status and chime messages, send
from the console:
•
If Chime is enabled, opening of a D/W sensor results in a multi-tone from the Chime.
•
Exit Delay for Arm gives single tone, every 4 seconds.
9.3 Using wired inputs
The SC28 console has two inputs for wired sensors. These sensors need to be of type NC (normally closed
contacts). There should not be any power on these inputs (potential-free / dry).
Connecting a wired sensor:
1. Open the top compartment on your console.
2. You will see two wired inputs.
3. Remove the wire bridge and connect your wired sensor.
4. Close the top compartment of your console and enter your PIN code to remove the word
TAMPER
from the
display.
5. The wired sensor is now ready for use.