P/N 033000=13610 Rev. 01-02-06 BMB Home Security
18
6.2 Panic alarm
The panic alarm can be switched on in case of an emergency, independent of whether the security system is
Armed or Disarmed.
The telephone message indicates the emergency sensor is triggered and that it is not the burglar alarm. This is
done by a default extra message to your own spoken telephone message. This standard multi-lingual message
is embedded into the system.
You can activate the panic alarm in two ways:
1. Activate the alarm via the KR18 Key Chain Remote Control
Keep the ARM and DISARM buttons of the remote control pressed simultaneously. The panic alarm is instantly
activated. Depending on the console settings the siren will or will not be activated (see 9.1).
2. Activate the alarm via the SH600 Comfort Remote Control
Press the red PANIC button. The panic alarm is instantly triggered. Depending on the console settings the siren
will be activated or not (see 9.1).
6.3 What happens when the alarm is tripped
1. Siren:
The built-in siren will be activated. You can choose to turn the siren off (silent alarm, see 9.1). If the
console is working on the emergency batteries, the siren will not be used, to save battery power.
2. The telephone dialler:
After the last digit of the first telephone number has been dialled, the spoken message
will be played and repeated several times. If the call is answered by pressing “0” from the receivers phone, the
console will stop calling. If the call is not answered, the second up to the sixth number are dialled until one of
these calls is confirmed by pressing “0”. The person who receives the phone call can listen to what is going on in
the building for one minute. The siren is switched off while you are listening in. The console will remain on alert.
If the alarm is triggered again later, the telephone dialler will be activated again and the complete procedure will
be repeated.
6.4 Disarming the system
Press DISARM on your remote control. The display will indicate the zone that is causing the alarm. To remove
this message, press ARM and then DISARM.
You can also switch off the system by entering your PIN code on the number pad of the console. After entering
your PIN code the display will read
DISARMED
.
6.5 Error messages
The numbers 1–32 in the display refer to up to 32 zones (read sensors). These represent up to 30 Door/Window
Sensors and/or Motion Detectors you install, plus the 2 hard wired zones. The numbers show open zones,
problem zones and bypassed zones by being displayed as steady on (door or window open), slow flash (there’s
a problem with that zone) or fast flash (that zone has been bypassed). Attempting to arm with an open or
problem zone makes the Console beep continuously and it will display in words on the display what the cause is,
but only for one zone at a time. Bypassing that zone (by pressing the CLEAR button) moves on to the next
problem zone, if there is one.
The status of all sensors is checked after the security system is switched on. If a problem is found, you will hear
the two-tone ‘
problem signal’
. If a sensor (e.g. zone 9) indicates there is a problem, a message is shown on the
display:
•
An open window or door:
OPEN ZONE 9
•
A tamper message:
TAMPER ZONE 9
•
Empty batteries or range problems:
PROBLEM ZONE 9
The console and the DS18 and MS18 Sensors are equipped with a tamper contact. If anyone tries to open the
console or sensor while the alarm is activated, the alarm will trip. If the alarm is NOT activated, you will see an
error message on the console’s display.
7. Prevention and comfort - ‘Home Automation’
7.1 Introduction
X10 Home Automation makes your home more comfortable, saves energy and offers security, both when you
are at home and away. For some people Home Automation means setting the lights with the same remote
control they use for the TV; for others it is a completely computerised system that is fully adjustable to their way
of life. X10 Home Solutions offers you the choice.
Your system is equipped with functions to secure your home. The system uses an intelligent process to control
the lighting in your house, so that it appears as if you are at home.
The X10 technology also offers you several so-called comfort functions. You can e.g. wireless control lamps
connected to Lamp/Dimmer Modules with your remote control or via the keypad on your console.