Blyss 3663602673026 Original Instructions Manual Download Page 9

16

NDY-19MA-E

In

 more 

detail

 . . .

17

NDY-19MA-E

Plug replacement

This appliance is supplied with a BS1363 pin plug fitted with a 13 Amp fuse. Should the 

fuse require replacement, it must be replaced with a fuse rated at 13 Amp and approved 

to BS1362. In the event the mains plug has to be removed/replaced for any reason, 

please note: 

IMPORTANT:

 The wires in the mains lead are coloured in accordance with 

the following code:

Blue or Black – N - (Neutral)

Brown or Red – L (Live)

Green / Yellow – E / (Earth)

Connect Blue 

to 

(Neutral)

Connect Green / 

Yellow to 

(earth)

13 AMP fuse 

approved to 

BS 1362

Brown 

(Live)

Cable grip

Outer sleeve 

firmly clamped

As the colours of the wires in the mains leadof this appliance may not correspond with 

the coloured markings identifying the terminals in your plug, proceed as follows. The 

blue wire must be connected to the terminal marked with an N or coloured black. The 

brown wire must be connected to the terminal marked with an L or coloured red.

WARNING!

 Never connect live or neutral wires to the earth terminal of the plug.

Only fit an approved 13 Amp BS 1363 or BS 1363/A plug and the correctly rated fuse.

If in doubt, consult a qualified electrician.

NOTE:

 If a moulded plug is fitted and has to be removed take great care 

in disposing of the plug and severed cable, it must be destroyed to prevent 

engaging into a socket.

Recycling and disposal

This symbol is known as the 'Crossed-out Wheelie Bin Symbol'.

When this symbol is marked on a product or battery, it means that

it should not be disposed of with your general household waste.

Some chemicals contained within electrical/electronic products or

batteries can be harmful to health and the environment.

Only dispose of electrical/electronic/battery items in separate

collection schemes, which cater for the recovery and recycling of

materials contained within. Your co-operation is vital to ensure

the success of these schemes and for the protection of the

environment.

 Recycling and disposal

 Cleaning and maintenance

16

17

Summary of Contents for 3663602673026











Reviews: