background image

10

11

NDY-19MA-E

NDY-19MA-E

In

 more 

detail

 . . .

In

 more 

detail

 . . .

Remote control

NOTE:

 The appliance should be powered on using the on/off switch before it 

can be operated using remote control.

- Switch the appliance on

- Set to standby mode

Go up in menu

(change day)

Set timer key

Cancel key

Timer on/off key

Toggle between 5 different 

flame dim levels

Press to activate low 

level heating 

Press to activate 

high level heating 

Go down in menu

(change day)

Set day/time

Confirm selection 

- Decrease temperature 

- Decrease hour/minute 

- Increase temperature 

- Increase hour/minute 

Set automatic heating 

mode

 

> The remote control requires 2x AAA size batteries (not included)

 

> Open the battery compartment by sliding the cover down and insert the batteries 

noting the polarity indicated in the battery compartment.

 

> Keep batteries out of reach of children.

 

> Remote control operations are identical to the functions on the control panel.

 

> The remote control must be point directly at the sensor on control pad.

Display

Temperature/ 

timer number 

Standby mode icon

Timer off

Timer on

Time/temperature display

Automatic heating mode

Flame dim level

Heating level

 - low heating level

 - high heating level

Day of the week

Timer icon

Settings

Setting weekday and time

 

1.  Press the   key. When the date is flashing press the “▲” or “▼” key to select the day. 

2.  Press the   key again, then press the “+” or “-” key to set the hour.

3.  Press the   key again, then press the “+” or “-” key to set the minute.   

4.  Press the   key to confirm the setting.

Setting temperature

NOTE:

 This setting is only applicable for the temperature in standard heating 

mode, not for the temperature in the timer mode. The default set temperature 

is 20 °C.

The appliance only starts working, when the set temperature is higher than 

the room temperature.  

Press the “+” or “-” key to set the temperature, which ranges from 15 to 30 °C. 

After the temperature setting has been completed, the display flashes about 5 seconds, 

then shows the room temperature.

Operation

Operation 

Summary of Contents for 3663602673026











Reviews: