manualshive.com logo in svg

BlueLine VORTEX 7000HHP, Manual

Share
Download
BlueLine VORTEX 7000HHP Manual Download Page 17

 

 

SECTION 2 

BLUE

LINE VORTEX 7000HHP 

 

13 

 

VACUUM SYSTEM 

See figure

 

3-2

. 

The vacuum flow is initiated by the 

vacuum

 

pump, or

 

blower. An air and water mixture 

is drawn into the vacuum inlet on the side of the 
truck. The mixture flows through a strainer basket 
in the pre-filter box, and then into the waste tank. 
The air exits the waste tank through a 100 mesh 
filtration system, into the vacuum pump. A 
vacuum pump relief valve is installed for vacuum 
pump protection. 

 

 
 

 
The air is discharged from the vacuum pump 
through a spiral silencer, then through a vacuum 
exhaust heat exchanger. 
 
A level shut off sensor is located near the top of 
the waste tank and will shut down the PTO (power 
take off) unit before the tank is at full capacity. 
This protects the vacuum pump from water 
damage. 

Note:

 Waste tank level shut off sensor 

will not

 shut the unit off due to high levels of 

foam.  The use of a quality defoamer is 
recommended. 
 

 

3-2 

 

Summary of Contents for VORTEX 7000HHP























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands