manualshive.com logo in svg

BlueLine VORTEX 7000HHP, Manual

Share
Download
BlueLine VORTEX 7000HHP Manual Download Page 1

INTRODUCTION 

BLUELINE VORTEX 7000HHP 

 

I

 

Congratulations 

on your purchase of the 

VORTEX MOBILE CLEANING UNIT

. 

This instruction/parts manual is a guide for 
operating and servicing your 

BLUE

LINE 

VORTEX 7000HHP

®

 mobile cleaning unit. 

 
Proper operation and service are necessary to 
ensure the outstanding performance of this unit.  
When properly maintained, your mobile cleaning 
unit will have a long and trouble-free life.  
 
The following service methods outlined in this 
manual are detailed in a manner that operation and 
servicing may be performed properly and safely. 
Because service levels vary due to the skill of the 
mechanic, tools and parts availability, ensure that 
prior to attempting any repair, you are familiar with 
this equipment and have the proper tools.  Any 
questions regarding the operation, service, or repair 
of this unit should be directed to your nearest 

BLUE

LINE dealer. 

 
The headings 

WARNING

 and 

CAUTION 

are 

utilized to warn you that steps must be taken to 
prevent personal injury or damage to the 
equipment.  Please make sure that you have read 
and understand these instructions entirely before 
proceeding with the operation of this unit. 
 
 
 

Record your units vehicle identification number 
here for future reference or if you should need to 
contact the factory in the future for any reason. 
 
VIN: 
 
This service and operations manual is written 
specifically for 

BLUE

LINE 

VORTEX 7000HHP

®

 

mobile cleaning unit manufactured by: 
 

BLUE

LINE EQUIPMENT LLC 

 
2604 Liberator Drive 
 
Prescott, AZ  86301     USA 
 

The information contained in this document is 
subject to change without notice and does not 
represent a commitment on the part of 

BLUE

LINE 

EQUIPMENT LLC. 
 
All rights reserved.  Copyright 2006 by 

BLUE

LINE EQUIPMENT LLC. No part of this 

work may be used or reproduced in any form or 
means without the express written consent and 
permission of 

BLUE

LINE EQUIPMENT LLC. 

 
Published by 

BLUE

LINE EQUIPMENT LLC. 

First printing:  October 2007 
Printed in USA 
 

 

 

 

 

VORTEX 7000HHP

®

 MANUAL 

PART# 49-034 

October, 07 

 

Summary of Contents for VORTEX 7000HHP























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands