BlueCreation BC111-DISKIT-001 Manual Download Page 15 | Manualshive

Page: 15 / 15

background image

BlueCreation

.

St John’s Innovation Centre Cowley

Road Cambridge CB4 0WS United Kingdom

t

.

+44 (0)1223 420 252

e

.

[email protected]

www.blue-creation.com

BC111-DISKIT-001

Manual

Step2) Download the latest driver from the FTDI website at the following link:

http://www.ftdichip.com/Drivers/VCP.htm

In the row for Windows in the comments column are the words setup executable, which is a link to download
the setup installer. This is the preferred method for installing this driver. When running the driver, if you do not
see the command window above re-run it. If after three tries you still have not seen it you may have another
issue such as insufficient permissions, anti-virus software or even malware preventing the install.

Hope this helps. Sometimes driver installations don't go as planned and the reasons may not be anything we
can diagnose and/or help with. However this guide covers those we can help with. Take care!

«
...
13
14
15

Summary of Contents for BC111-DISKIT-001
















Reviews:

No comments

Related manuals for BC111-DISKIT-001

Brand: Quantum Pages: 69

Brand: MSI Pages: 186

Brand: Supero Pages: 107

Brand: Texas Instruments Pages: 25

Brand: Vector Pages: 73

Brand: Microchip Technology Pages: 35

Brand: Texas Instruments Pages: 19

Brand: Vox Pages: 93

PROTO1 Xplained Pro

Brand: Atmel Pages: 17

Brand: AOpen Pages: 8

Brand: u-blox Pages: 37

Brand: SOYO Pages: 99

Brand: THine Pages: 13

Brand: Consumer Microcircuits Pages: 58

Brand: Shuttle Pages: 69

Brand: Shuttle Pages: 81

Brand: Shuttle Pages: 82

Brand: Shuttle Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands