BlueCreation BC111-DISKIT-001 Manual Download Page 1

Page: 1 / 15

BlueCreation

St John’s Innovation Centre Cowley

Road Cambridge CB4 0WS United Kingdom

+44 (0)1223 420 252

[email protected]

www.blue-creation.com

BC111-DISKIT-001

Manual

Key Specifications



Bluetooth Low Energy dedicated development kit



4.0 Bluetooth Low Energy (BLE, Bluetooth SMART)

Mode



Integrates BC111 module and Melody SMART software



Access to UART via USB (FTDI on board)



Direct access to GPIOs



GAP, ATT, GATT, L2CAP and SMP Bluetooth profiles



FCC, CE, IC and Bluetooth certified

Applications



Smart Phone Controlled Accessories



Fitness and Healthcare Accessories



Smart-Home Controllers



Smart Appliances



Remote Controls and Smart TVs



General Bluetooth Controllers

Melody
Smart App

Description

BC111-DISKIT-001 is a development board that
allows engineers to quickly prototype any
Bluetooth device using Melody SMART and high
level commands. It is the ideal kit to start
working with 4.0 Bluetooth Low Energy (BLE,
Bluetooth SMART)

Summary of Contents for BC111-DISKIT-001
















Search results

Summary of Contents for BC111-DISKIT-001

Reviews:

Related manuals for BC111-DISKIT-001

Brands by name

Popular brands

BlueCreation BC111-DISKIT-001, Manual

Search results

Summary of Contents for BC111-DISKIT-001

Reviews:

Related manuals for BC111-DISKIT-001

Brands by name

Popular brands