background image

December 2006 

 

Blue Sky Network 

100115 

C-1000A Iridium™ Satellite Phone System

 Page 

5

 

System Operation 

The C-1000A Satellite Phone System uses a 2-wire Plain Old Telephone System 
(POTS) telephone, a 4-wire analog phone or the C-1000A Cabin Unit with the 
Motorola Digital handset as the primary interface between the operator and the 
system. However, a PC can be used for data communications via the PC’s serial port 
connection to the Cabin Unit. System configuration procedures are covered in 
Motorola’s 

Satellite Series 9520 Mobile Telephone User’s Guide

. Not all features 

listed in the 9520 User’s Guide are available in the C-1000A, since the system was 
adapted for aviation. The Motorola 9520 guide can be found on the Internet through 
the link 

http://www.blueskynetwork.com/Support/UserGuides.php

Placing a Call 

General 

Since the Iridium phone is designed to operate from anywhere on the globe, the 
Iridium phone network and phone numbers are configured like an independent 
country.  

Every Iridium call must be dialed like an international call.

 You operate 

the phone the same way no matter where you are located. 

2-Wire POTS or 4-Wire Analog Phone 

1.  Enter the phone number in an international format as follows:  

Pick up handset and verify you have dial tone, then dial

 00

 followed by 

the Country Code, the City or Area Code and the Phone Number 

Motorola Digital Handset (C-1000A Cabin Unit) 

Reference Motorola’s 

Satellite Series 9520 Mobile Telephone User’s Guide

 for 

instructions on using the C-1000A Cabin Unit Digital Handset 

To place a call using the Motorola Digital Handset on the C-1000A Cabin Unit 

1.  Enter the phone number in an international format as follows:  

Dial 

00

 or  

+

  followed by the Country Code, the City or Area Code and 

the Phone Number 

NOTE:

  The “

+

” sign is obtained by pressing and holding the 

0+

 key for a few seconds 

2. Press the 

OK

 button. You will see “Calling” displayed on the handset 

followed by the number you dialed 

Receiving a Call 

2-Wire POTS or 4-Wire Analog Phone 

Reference the phone’s user manual, or try simply picking up the handset. 

Motorola Digital Handset (C-1000A Cabin Unit) 

To answer an incoming call, simply unlatch the handset or if you are using a 
headset, press the 

OK

 button on the Motorola Handset. For further information, 

reference Motorola’s 

Satellite Series 9520 Mobile Telephone User’s Guide

 for 

instructions on using the C-1000A Cabin Unit Digital Handset. 

Summary of Contents for Iridium C-1000A














































Reviews: