Blue Sea Systems 7725, Manual

Page: 1 / 2

PN 7725 / PN 7725B
PN 7725 includes a connector plug for the ATO
®
/ATC
®
fuse circuits
The Blue Sea Systems SafetyHub 100 is an ignition-protected fuse block
with an integrated connecting plug. It consolidates 1A
– 200A fuses, and can
be wired directly to the battery (for unswitched fuse protection) or after the
battery switch (for switched fuse protection).
]
Disconnect all battery connections before beginning the installation.
]
Blue Sea Systems strongly recommends that a competent electrical
professional perform the installation of this product.
GUARANTEE: Blue Sea Systems stands behind its products
for as long as you own them. Find detailed information at
www.bluesea.com/about. For customer service, call 800-222-7617.
Marine Electrical Products
SafetyHub 100 Fuse Block
Blue Sea Systems Inc. p 360.738-8230
425 Sequoia Drive f 360.734-4195
Bellingham, WA 98226 USA conductor@bluesea.com
www.bluesea.com
980004720 Rev.004
Specifications
WARNING
Amperage Maximum Operating (combined) (see table below)
Nominal Operating Voltage 12V DC
Minimum Input Cable Size to Meet Ratings 4/0 AWG (120 mm²)
Recommended Ring Terminal M8 (5/16”)
Stud Size M8 x 1.25
Stud Torque 15 ft-lb (20.3 N-m)
AMI
®
/MIDI
®
Fuse Block
Amperage Maximum Operating (per block) 240A
†
Amperage Maximum Operating (per circuit) 170A
†
Fuse Amperages Available 30A–200A
Minimum Cable Size to Meet Ratings 2/0 AWG (70 mm²)
Screw Size M5 x .8 x 10
Screw Torque 27 in-lb (3.0 N-m)
ATO
®
/ATC
®
Fuse Block
Amperage Maximum Operating (per block) 50A
†
Amperage Maximum Operating (per circuit) 20A
†
Fuse Amperages Available 1A–20A
Regulatory
E
marked
Meets ISO 8846 ignition protection and SAE J1171 external ignition protection requirements.
IP66—protected against powerful water jets
Input Wire Size and Current Derating Table
† Ratings are dependent on input cable sized for appropriate amperages.
Unlatch the two yellow tabs on the fuse cover to access fuses.
The ATO
®
/ATC
®
Fuse Block of the SafetyHub 100 is used for low-amp circuits.
The total continuous amperage of this block must not exceed 50A.
The AMI
®
/MIDI
®
Fuse Block of the SafteyHub 100 is used for high-amp circuits.
The total continuous amperage of this block must not exceed 240A
AWG Wire Size Metric Wire Size Amperage Maximum Operating (combined)
4/0 AWG 120 mm² 280A
2/0 AWG 70 mm² 225A
1 AWG 50 mm² 180A
4 AWG 25 mm² 125A
PN 7725 / PN 7725B
PN 7725 includes a connector plug for the ATO
®
/ATC
®
fuse circuits
The Blue Sea Systems SafetyHub 100 is an ignition-protected fuse block
with an integrated connecting plug. It consolidates 1A
– 200A fuses, and can
be wired directly to the battery (for unswitched fuse protection) or after the
battery switch (for switched fuse protection).
]
Disconnect all battery connections before beginning the installation.
]
Blue Sea Systems strongly recommends that a competent electrical
professional perform the installation of this product.
GUARANTEE: Blue Sea Systems stands behind its products
for as long as you own them. Find detailed information at
www.bluesea.com/about. For customer service, call 800-222-7617.
Marine Electrical Products
SafetyHub 100 Fuse Block
Blue Sea Systems Inc. p 360.738-8230
425 Sequoia Drive f 360.734-4195
Bellingham, WA 98226 USA conductor@bluesea.com
www.bluesea.com
980004720 Rev.004
Specifications
WARNING
Amperage Maximum Operating (combined) (see table below)
Nominal Operating Voltage 12V DC
Minimum Input Cable Size to Meet Ratings 4/0 AWG (120 mm²)
Recommended Ring Terminal M8 (5/16”)
Stud Size M8 x 1.25
Stud Torque 15 ft-lb (20.3 N-m)
AMI
®
/MIDI
®
Fuse Block
Amperage Maximum Operating (per block) 240A
†
Amperage Maximum Operating (per circuit) 170A
†
Fuse Amperages Available 30A–200A
Minimum Cable Size to Meet Ratings 2/0 AWG (70 mm²)
Screw Size M5 x .8 x 10
Screw Torque 27 in-lb (3.0 N-m)
ATO
®
/ATC
®
Fuse Block
Amperage Maximum Operating (per block) 50A
†
Amperage Maximum Operating (per circuit) 20A
†
Fuse Amperages Available 1A–20A
Regulatory
E
marked
Meets ISO 8846 ignition protection and SAE J1171 external ignition protection requirements.
IP66—protected against powerful water jets
Input Wire Size and Current Derating Table
† Ratings are dependent on input cable sized for appropriate amperages.
Unlatch the two yellow tabs on the fuse cover to access fuses.
The ATO
®
/ATC
®
Fuse Block of the SafetyHub 100 is used for low-amp circuits.
The total continuous amperage of this block must not exceed 50A.
The AMI
®
/MIDI
®
Fuse Block of the SafteyHub 100 is used for high-amp circuits.
The total continuous amperage of this block must not exceed 240A
AWG Wire Size Metric Wire Size Amperage Maximum Operating (combined)
4/0 AWG 120 mm² 280A
2/0 AWG 70 mm² 225A
1 AWG 50 mm² 180A
4 AWG 25 mm² 125A