![background image](http://html.mh-extra.com/html/blue-chip/bct-etx-c3-xxx/bct-etx-c3-xxx_user-manual_2775488025.webp)
BCT-ETX-C3-XXX
S
INGLE
B
OARD
C
OMPUTER
I
NSTALLATION
IOCS16#
The IOCS16# signal determines when a 16-bit to 8-bit conversion is needed for I/O bus cycles. A conversion is
done any time the CPU module requests a 16-bit I/O cycle while the IOCS16# line is high. If IOCS16# is high,
16-bit CPU cycles are automatically converted on the bus into two 8-bit cycles. If IOCS16# is low, an access to
peripherals is performed 16 bits wide.
REFRESH#
REFRESH# is pulled low whenever a refresh cycle is initiated. A refresh cycle is activated every 15.6 us in order
to prevent loss of DRAM data.
0WS#
The Zero wait state signal tells the CPU to complete the current bus cycle without inserting the default wait
states. By default the CPU inserts 4 wait states for 8-bit transfers and 1 wait state for 16-bit transfers.
MASTER#
This signal is used with a DRQ line to gain control of the system bus. A processor or a DMA controller on the
I/O channel may issue a DRQ to a DMA channel in cascade mode and receive a DACK#. Upon receiving the
DACK#, a bus master may pull MASTER# low, which will allow it to control the system address, data and
control lines. After MASTER# is low, the bus master must wait one system clock period before driving the
address and data lines, and two clock periods before issuing a read or write command. If this signal is held low
for more than 15 us, system memory may be lost as memory refresh is disabled during this process.
SYSCLK
SYSCLK is supplied by the CPU module and has a nominal frequency of about 8 MHz with a duty cycle of 40-
60 percent. The frequency supplied by different CPU modules may vary. This signal is supplied at all times
except when the CPU module is in sleep mode.
OSC
OSC is supplied by the CPU module. It has a nominal frequency of 14.31818 MHz and a duty
cycle of 40-60 percent. This signal is supplied at all times except when the CPU module is in
sleep mode.
RESETDRV
This active-high output is system reset generated from CPU modules. It is responsible for
resetting external devices on the ISA Bus.
DREQ[0, 1, 2, 3, 5, 6, 7]
The asynchronous DMA request inputs are used by external devices to indicate when they need service from the
CPU modules DAM controllers. DREQ0..3 are used for transfers between 8-bit I/O adapters and system
memory. DREQ5..7 are used for transfers between 16-bit I/O adapters and system memory. DRQ4 is not
available externally. All DRQ pins have pull-up resistors on the CPU modules.
DACK[0, 1, 2, 3, 5, 6, 7]#
DMA acknowledge 0..3 and 5.7 are used to acknowledge DMA requests. They are active-low.
TC
The active-high output Terminal Count indicates that one of the DMA channels has transferred all data.
IRQ[3..7, 9,15]
These are the asynchronous interrupt request lines. IRQ0, 1, 2 and 8 are not available as external interrupts
because they are used internally on the CPU module. All IRQ signals are active-high. The interrupt requests are
prioritized. IRQ9 through IRQ12 and IRQ14 through IRQ15 have the highest priority (IRQ9 is the highest).
IRQ3 through IRQ7 have the lowest priority (IRQ7 is the lowest). An interrupt request is generated when an IRQ
line is raised from low to high. The line must be held high until the CPU acknowledges the interrupt request
(interrupt service routine).