Blonder tongue SDE-6S-ASI User Manual Download

Page: 7 / 40

SDE-6S-ASI

User Manual

Description:

Front panel connectors and indicators:

POWER LED:

This will be Green if unit is powered. Off when there is no power.

POWER

DESCRIPTION

Green

Unit is powered on and the power supply is functioning properly.

Off

Unit power is disconnected/switched off, or the power input fuse is blown/the power supply has failed

Table 1: Front Panel LED Indicators - POWER

INPUT LED:

This input LED will be Green when all the inputs that are configured through the webpage and they are

working. If even one input is not connected when it should be then the LED will be red. The analog Audio inputs

are not part of this input Status LED condition.

STATUS LED / SOFTWARE STATUS LED:

This LED will be Green when software is running in Normal mode.

DVI TEST OUT:

Multi-Channel output suitable for preview and monitoring of the ASI output.

STATUS

INPUT

DESCRIPTION

Green

Normal Operation

Green

Blinking Green-Yellow

EAS Video Switch Over Activated

Green

Red-Off-Red-Off

Video Input or ASI Input Signal Loss Detected for an Off-Air Service

Table 2: Front Panel LED Indicators – Normal Broadcast Operations

STATUS

INPUT

DESCRIPTION

Blinking Green

System Booting / Starting-Up

Blinking Red-Yellow or Red-Green

High Temperature Warning

Red

High Temperature Error System has shut down

Red

Invalid or Failed SFP Device Detected in IP-1 Socket

Red

Yellow

Invalid or Failed SFP Device Detected in Socket IP-2, 3 or 4

Red

Off

Failure Detected in System Hardware, BIST or Boot-up

Table 3: Front Panel LED Indicators – System Integrity and Status

Summary of Contents for SDE-6S-ASI









































Search results

Summary of Contents for SDE-6S-ASI

Reviews:

Related manuals for SDE-6S-ASI

Brands by name

Popular brands

Blonder tongue SDE-6S-ASI, User Manual

Search results

Summary of Contents for SDE-6S-ASI

Reviews:

Related manuals for SDE-6S-ASI

Brands by name

Popular brands