Blonder tongue SDE-6S-ASI User Manual Download | Manualshive

Page: 13 / 40

background image

13

SDE-6S-ASI

User Manual

Section 3 – Installation & Power-up

3.1 Unpacking

You will find the following items in the box:

• SDE-6S-ASI-- Encoder (QTY=1)
• Power Cord with IEC C13 line socket and 3-pin Type B NEMA 5 plug (QTY=1)
• A hardware bag (item 741022200) containing the following:

Seven-foot cross-pinned (cross-over) RJ45 Ethernet cable (QTY=1)
SFP Transceiver (QTY-2)
4 Pin Plug (QTY=1)
12 Pin Plug (QTY=1)
10 Pin Plug (QTY=8)
Six-foot DVI to HDMI cable (QTY=1)

3.2 Installation

The SDE-6S-ASI encoder is designed to be installed in a standard 19-inch (483 mm) rack (EIA 310-D, IEC 60297, and DIN 41494

SC48D).
To install the encoder, secure the unit’s front panel to the rack by inserting four (4) machine screws, with cup washers,

through the four (4) mounting holes in the front panel.

3.3 Power-up

110/230 VAC Encoders (Stk# 6365) :

Connect the line cord to a 110/230 VAC, 60/50 Hz outlet. Please note that the IEC power connector on the rear panel of

the unit is equipped with an ON/OFF switch and a fuse (SLO-BLO, 3.0 Amp, 250V). The “POWER” LED on the front-panel

will light green.

-48 VDC Encoders (Stk# 6365 48) :

Connect the positive and negative leads from the batteries to the rear panel terminal strip.

For safe and reliable operation, the ground pin of the power cord plug must be grounded properly.

«
...
11
12
13
14
15
...
»

Summary of Contents for SDE-6S-ASI









































Reviews:

No comments

Related manuals for SDE-6S-ASI

Brand: Wyrestorm Pages: 4

Brand: Digitrax Pages: 8

Brand: Gorman-Redlich Pages: 3

MAXX SST VEC049GM

Brand: Vector Pages: 10

Brand: EBARA Pages: 34

Brand: Lika Pages: 2

OBID i-scan ID ISC.ANT.PS-A

Brand: Feig Electronic Pages: 28

Brand: ICP DAS USA Pages: 8

Brand: Vanner Pages: 28

Brand: Hamron Pages: 28

Pro Enigma MI-X450

Brand: Aiwa Pages: 13

Brand: Linksys Pages: 2

Brand: LC Pages: 44

Brand: Xantrex Pages: 344

Brand: GoMax Electronics Pages: 12

Omnitron iConverter GX/TM2

Brand: Omnitron Systems Technology Pages: 2

E70ACMS4 Series

Brand: Lenze Pages: 20

Brand: Spectare Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands