Blonder tongue FlexCoder 6582 User Manual Download Page 26

Page: 26 / 28

26 FlexCoder

Instruction Manual

System Mode Select (Reboot Only):

allows the user to switch between Demux, Mux and Pass-Thru modes. Changes are

applied after a System Reboot. (Factory Default: Demux)

System Reboot:

allows the user to reboot the unit.

IGMP Version Support:

is selectable support for IGMPv2 or IGMPv3.

System Watchdog:

options are “Enabled” and “Disabled”. When Enabled, automatically reboots the unit, if the operating

system stops working.

Remote Control IP Address:

the static IP address that is assigned to the Control 100/1000 Port. It allows the user to access

the unit via the web interface. (Factory Default: 172.16.70.1)

Remote Control Subnet Mask:

the Subnet Mask assigned to the Control Port of the unit. It allows the user to determine

which subnet the Control Port IP address belongs to. (Factory Default: 255.255.255.0)

Remote Control Default Gateway:

the gateway address assigned to the Control Port. It allows the user to access the unit

from another network via the web interface. (Factory Default: 172.16.70.254)

Data IP Address:

the static IP address that is assigned to the Data Port.

Data Subnet Mask:

the Subnet Mask assigned to the Data Port of the unit.

Data Default Gateway:

the gateway address assigned to the Data Port.

Event Log Destination:

the IP address of the remote server, to which Syslog sends the activities recorded by the unit for

monitoring and troubleshooting purposes. (Factory Default: 172.16.70.2)

Log Destination Port #:

the Error Log Destination port to which a duplicate of the error messages created by the unit can be

forwarded for monitoring and troubleshooting purposes. (Unmodifiable Factory Default: 514)

Time Server IP:

the IP address for the Time Server from where the unit can obtain its clock reference (see Section 4.9 for

details). (Factory Default: 172.16.70.2)

Syslog Errors:

enable/disable encoder to forward error messages (in red font) to the Syslog. (Factory Default: Disabled)

Syslog Informational:

enable/disable encoder to forward informational messages (in blue font) to the Syslog. (Factory

Default: Disabled)

Syslog Feedback:

enable/disable the encoder to forward feedback or confirmation messages (in green font) to the Syslog.

(Factory Default: Disabled)

4.12 “Admin” Screen (continued)

Remember

click

the

SAVE

button

apply

the

new

values/configurations.

22
23

27
28
29
30

33
34

Summary of Contents for FlexCoder 6582





























Search results

Summary of Contents for FlexCoder 6582

Reviews:

Related manuals for FlexCoder 6582

Brands by name

Popular brands

Blonder tongue FlexCoder 6582, User Manual

Search results

Summary of Contents for FlexCoder 6582

Reviews:

Related manuals for FlexCoder 6582

Brands by name

Popular brands