3
Safety issues
WARNING: ONE SHOULD
AVOID CREATING IGNITION
SOURCES, LIKE HEAT, AS A
RESULT OF THE USE OF THE
TOOL WITH OTHER TOOLS
OR EQUIPMENT.
WARNING: THE WARNING
PLATES, SIGNS AND LABELS
MUST BE PRESENT ON THE
TOOL. DO NOT REMOVE
THE LABELS. IF THEY ARE
MISSING, REPLACING IS
MANDATORY.
WARNING: ALL WARNING
PLATES, SIGNS AND
LABELS ATTACHED TO
THE EQUIPMENT MUST BE
OBSERVED.
WARNING: DO NOT USE
THE TOOL FOR ANY OTHER
PURPOSE THAN MAKING UP
AND BRAKING OUT WITHIN
ITS SPECIFICATION.
WARNING: FAILURE TO
CONDUCT ROUTINE
MAINTENANCE COULD
RESULT IN EQUIPMENT
DAMAGE OR INJURY TO
PERSONNEL.
WARNING: THE TOOL MUST
ONLY BE SERVICED BY
TRAINED B+V PERSONNEL
OR BY AUTHORIZED
PERSONNEL.
WARNING: WEAR PERSONAL
PROTECTION EQUIPMENT
WHILE WORKING WITH THE
EQUIPMENT.
WARNING: IF ANY
SAFETY ELEMENTS (LIKE
SAFETY ROPES, WIRE,
SAFETY SHEETS, PLATES
OR WASHERS) WERE
DISASSEMBLED DUE TO
MAINTENANCE WORK, DO
NOT RE-USE THEM. ALWAYS
REPLACE THEM WITH NEW
SAFETY ELEMENTS.
WARNING: KEEP HANDS
AND ARMS CLEAR OF
ALL MOVING PARTS
WHEN CONNECTING,
DISCONNECTING OR
OPERATING THE UNIT.
WARNING: ALWAYS WEAR
PROTECTIVE GEAR FOR
EYES, HEAD, HANDS AND
FEET.
WARNING: WHEN SERVICING
UNIT, BE SURE ALL POWER
IS OFF AND SUPPLY LINES
ARE DISCONNECTED AND
INTERNAL PRESSURE IS
BLED FROM THE TOOL.
WARNING: LUBRICATE UNIT
ONLY WHEN SUPPLY LINES
ARE DISCONNECTED AND
HPU IS OFF AND TAGGED
OUT. VERIFY THAT SYSTEM
PRESSURE IS -0- PSI.
WARNING: ALWAYS USE
LIFTING APPARATUS
(SLINGS, CABLES,
SHACKLES AND THE
LIKE) THAT HAVE BEEN
INSPECTED AND ARE IN
GOOD CONDITION AND ARE
PROPERLY SIZED. ENSURE
THAT ALL RIGGING AND
LIFTING PROCEDURES
ARE IN ACCORDANCE
WITH ACCEPTED
OILFIELD PRACTICES AND
STANDARDS.
WARNING: ALWAYS
CHECK THE UNIT FOR
LOOSE FASTENERS AND
HYDRAULIC CONNECTIONS
AS WELL AS ANY OTHER
DAMAGE PRIOR TO TURNING
ON THE POWER UNIT.
Revision History Table
REV.
SECTION SUB-SEC. PARA. CHANGE REQUEST #
DATE
AUTHORIZED BY
Draft
All
All
All
N/A
10/01/10
KJ
0
All
All
All
N/A
03/19/12
KJ
Summary of Contents for GraySpin Mark 40
