Blink WE-30C Owner'S Manual Download | Manualshive

Page: 48 / 63

background image

44

OM0001_L2_R_WM_USAv2.1

Device Info

Date & Time

Touch the

Device Info

option and this

screen is displayed with your Blink

unit’s

information. This will be helpful in
troubleshooting your Blink device.

Set the time and date on your Blink charging
system or allow the Blink system to set it
automatically (default setting).

See page 17 for directions.

«
...
46
47
48
49
50
...
»

Summary of Contents for WE-30C
































































Reviews:

No comments

Related manuals for WE-30C

Brand: Daewoo Pages: 10

Brand: Parallel Audio Pages: 4

Brand: Napa Pages: 31

XD COLLECTION P308.82 Series

Brand: XINDAO Pages: 10

Brand: i-tec Pages: 32

Brand: SUHNER ABRASIVE Pages: 56

Brand: ToughTested Pages: 6

Brand: SkillKorp Pages: 17

Brand: RC-Plus Pages: 24

Brand: PATONA Pages: 44

Brand: Hama Pages: 2

Brand: Overlander Pages: 20

Brand: Huawei Pages: 208

Brand: LG Pages: 5

Brand: LG Pages: 8

Brand: LG Pages: 2

Brand: Philips Pages: 2

Brand: Blackweb Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands