manualshive.com logo in svg

Blaze E6IO, Manual

Share
Download
Blaze E6IO Manual Download Page 7

7

SAFETY

DANGER

MONOXYDE DE CARBONE

Cette appareil peut produire du monoxyde de carbon, 

un gas indore.

L’utilisation de cet appareil dans des espaces clos peut 

entraîner la mort.

Ne jamais utiliser cet appareil dans un espace clos 

comme un véhicule de camping, une tente, une 

automobile ou une maison.

DANGER

S'il y a une odeur de gaz:

• 

Coupez l'admission de gaz de l'appareil.

•  Éteindre toute flamme nue.

• 

Si l'odeur persiste, éloignez-vous de l'appareil et appelez immediatement 

le fournisseur de gaz ou le service d'incendie.

ADVERTISSEMENT

Ne pas entreposer ni utiliser de l'essence ni d'autres vapeurs ou liquides 

inflammables dans le voisinage de l'appareil, ni de tout autre appareil.

Une bouteille de propoane qui n'est pas raccordée en vue de son utilisation, 

ne doit pas être entreposée dans le voisinage de cet appareil ou de tout     

autre appareil.

ADVERTISSEMENT

Une installation, un ajustement, une modification, une résparation ou un 

entretien inapproprié peuvent être la cause de blessures ou de dommages. 

Veuillez lire attentivement les instructions d'installation, d'utilisation et d'en-

tretien avant d'installer ou de réparer ce materiel.

SAMPLE

Summary of Contents for E6IO

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands