manualshive.com logo in svg

Blaze E6IO, Manual

Share
Download
Blaze E6IO Manual Download Page 34

34

High temp 

silicone

SUPPLEMENTAL MATERIAL

34

Chimney Fan

Under conditions with extremely strong winds 

surrounding the top of the chimney, the chimney fan 

must be secured by steel wires supplied with the fan.

CAUTION

Single Fan on Steel Chimney

Step 1: Prepare fan location

The steel chimney adapter (SCA) slides right into the 

chimney, where the long collar engagement ensures 

safe anchoring. 

Step 2: Preparation of fan

Locate the installation brackets in the grooves on the 

underside of the fan base, using the bolts and nuts 

supplied to secure the brackets. Note that the bolts 

shall be installed from the bottom side in the two inner 

holes.

Adjust the final position of the installation brackets 

ensuring that there is a small gap between the brack

-

ets and the flue wall/adapter throat. Tighten the nuts. 

If the brackets touch the flue wall, it may create some 

vibration noise.

Step 3: Attaching the fan

The chimney fan is now ready for installation on the 

top of the chimney. It is not necessary to bolt the fan 

to the chimney.

Wall Mounting of Chimney Fan

When mounting the chimney fan on a wall, the instal

-

lation instructions for installation on a steel chimney 

should be followed. Use of the adapater SCA can 

make the installation easier.

To ease installation, detach the fan base by removing 

the bolts holding the hinges together. Center the fan 

base over the outlet and bolt the base onto the wall 

with the hinges pointing upwards.

After mounting the base securely, attach the fan mo

-

tor housing by reassembling the fan hinges. Seal with 

high temp silicone all around the edges.

SAMPLE

Summary of Contents for E6IO

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands