manualshive.com logo in svg

Blaze King CLARITY CL2714.SP, Operation & Installation Manual

Share
Download
Blaze King CLARITY CL2714.SP Operation & Installation Manual Download Page 28

180-CL2714.SP v1.00

July 30, 2020

Page 28

Clarity CL2714 SP

INSTALLATION

INITIAL SETUP

1. 

There are six leveling bolts on the appliance 

as shown in (

Fig.9

).  Level the appliance from 

side to side and front to back.  Adjust the 

leveling bolts to desired vertical position so the 

appliance is level.  The bolts can be removed if 

necessary. 

2.  Remove the safety screen trim, and door glass. 

(see 

SAFETY SCREEN TRIM AND GLASS 

DOOR REMOVAL

), set safety screen trim 

aside. 

3.  REMOVE THE STATIC CLING LABEL THAT 

IS ON THE DOOR GLASS

.  Hold glass to 

frame when removing as it is only held in place 

with silicone.  Set the door glass assembly 

aside. 

4. 

If installing the optional S.0402 FIREBOX 

GLASS KIT (3 piece) or the S.0602 FIREBOX 

GLASS KIT (4 piece) then refer to their 

respective installation instructions.

 

5.  If installing the optional S.0519 LOG SET 

DRIFT CLARITY (5PC) or S.0529 LOG SET 

DRIFT CL2714 (7PC) then refer to their 

respective installation instructions.

 

6.  Repeat “

GLASS DOOR REMOVAL

” steps in 

reverse order to complete initial setup.

Fig.9

S.0529 LOG SET (7 piece)

S.0519 LOG SET (5 piece)

Summary of Contents for CLARITY CL2714.SP













































Reviews:

No comments

Brands by name

Popular brands

Load more brands