manualshive.com logo in svg

Blaze King CLARITY CL2714.SP, Operation & Installation Manual

Share
Download
Blaze King CLARITY CL2714.SP Operation & Installation Manual Download Page 20

180-CL2714.SP v1.00

July 30, 2020

Page 20

Clarity CL2714 SP

820 NOVA 

installation

iinnssttrruuccttiioonnss

HI/LO Conversion Kit

WARNING!

The installation of this conversion kit must only be undertaken by a

qualified and certified gas appliance installer.

WARNING!

This HI-LO conversion kit must ONLY be applied as part of a conversion kit

supplied by the APPLIANCE MANUFACTURER for the specific appliance, and

type of gas, being converted.

INSTALLER NOTICE. These instructions must be left with appliance.

1

2

3

4

5

6

7

This installation or replacement instruction refer to HI-LO pressure 

regulator kit to be used to convert the 820 Nova Combination Gas Control 

with adjustable pressure regulator into manual HI-LO. The same kit can

also be used for the conversion from LP to Natural Gas and vice versa of

the 820 Nova with manual HI-LO.

7.252.021   001

Turn control knob to the OFF position,
and shut off the gas supply to the
valve.

Using a Torx T20, or slotted screwdriver,
remove and discard the three pressure
regulator mounting screws (A), pressure
regulator tower (B), and the spring and
diaphragm assembly (C).

Ensure the rubber gasket (D), which is
prefitted as part of assembly (E), is
properly positioned and install the new
HI/LO pressure regulator assemble
using the supplied screws (F). 
Tighten screws securely.
(Reference torque = 25 lb·in).

Install the enclosed identification label
(G) to the valve body where it can be
easily seen.

Apply gas to system and re-light
appliance according to manufacturers
instructions.

With the main burner “ON”, test the
new pressure regulator assembly for
leaks using a soap solution.

Relight the main burner in both the HI,
and LO positions, and verify proper
burner ignition and operation.

TT L LOO II P P

O OTT

00

NN

L L

00FF

P PII

FF

C

C

B

B

A

A

HIHI

LO

LO

P PIIOOLL

TT

T T O O

NN 00

P P

FF

I I

FF

00

L L

A

A

C

C

B

B

G

G

P PII

L L

O OTT

00

NN

I ILLOOTT

00FFFF

P P

D

D

E

E

F

F

F

F

HIHI

LO

LO

MAINTENANCE and SERVICE

Summary of Contents for CLARITY CL2714.SP













































Reviews:

No comments

Brands by name

Popular brands

Load more brands