Blaze King CLARITY CL2714.SP Operation & Installation Manual Download | Manualshive

Page: 25 / 44

background image

180-CL2714.SP v1.00

July 30, 2020

Page 25

Clarity CL2714 SP

S.Z4946.SP BLOWER INSTALLATION

1.

If attached, lift face frame and safety screen up

and out, away from the appliance, and set it aside.

2.

The blower may be installed prior to appliance

installment by removing the back blower access

cover. If the appliance is already installed go to

step 5.

3.

Affix the blower to the access cover as shown, the

blower edge should be against the cover flange.

4.

Feed blower wires and assembly through opening

and reattach the access cover.

5. Feed the power cord wires through the case hole.

6. Slide the loomex bushing into the case hole.

7.

Rotate the loomex bushing so slots are offset.

OPTIONAL BLOWER

«
...
23
24
25
26
27
...
»

Summary of Contents for CLARITY CL2714.SP













































Reviews:

No comments

Related manuals for CLARITY CL2714.SP

Brand: komodo Pages: 40

Brand: Majestic Pages: 76

Brand: Ignis Pages: 16

Brand: Fondis Pages: 33

Brand: FocalPoint Pages: 11

Inglenook IWZC-02

Brand: Country Flame Pages: 54

Brand: Heatilator Pages: 88

Brand: Regency Fireplace Products Pages: 44

Brand: Valcourt Pages: 6

Brand: Majestic Pages: 36

Brand: Royal Pages: 56

Brand: Heat&Glo Pages: 85

Brand: lifeSMART Pages: 18

Brand: Pacific energy Pages: 28

Brand: Pacific energy Pages: 34

Brand: Lennox Pages: 8

Brand: Lennox Pages: 24

Brand: Quadra-Fire Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands