Blaupunkt Bremen CD72 Operating Instructions Manual Download | Manualshive

Page: 14 / 49

background image

59

DANSK

ENGLISH

DEUTSCH

FRANÇAIS

IT

ALIANO

NEDERLANDS

SVENSKA

ESP

AÑOL

PORTUGUÊS

Setting the telephone volume level

You can set the volume of incoming tel-
ephone calls.

➮

Press the MENU button

8

.

➮

Press the softkey

4

assigned to

the “VOL” display item.

➮

Press the softkey

4

assigned to

the “TEL” display item.

➮

Set the required volume using the
volume control

1

.

➮

Press the joystick OK

7

to save

your settings or the MENU button

8

to close the menu without sav-

ing.

Note:

●

You can also adjust the volume
during the telephone call using the
volume control

1

. This setting ap-

plies to the current call and is not
saved.

Navigation audio

Instead of connecting a second exter-
nal audio source (“AUX2”, see “Exter-
nal audio sources”), you can connect a
navigation system.

If your car radio is connected to a navi-
gation system and the navigation sys-
tem outputs spoken information, the
navigation voice output will be “mixed
in” with the current audio source and
will be outputted over the car radio’s
loudspeakers.

This requires that the navigation sys-
tem is connected to the car radio as
described in the installation instructions
and is activated in the menu.

You can find out from your Blaupunkt
dealer which navigation systems can be
used with your car radio.

Activating navigation audio

You can either connect a second exter-
nal audio source or a navigation sys-
tem to this device. To do so, you must
open the menu in order to set the de-
vice that is connected.

➮

Press the MENU button

8

.

➮

Press the softkey

4

assigned to

the “SETP” display item.

➮

Press the softkey

4

assigned to

the “AUX2” display item.

➮

Press the softkey

4

assigned to

the “NAVI” display item if a naviga-
tion system is connected.

➮

Press the joystick OK

7

to save

your settings or the MENU button

8

to close the menu without sav-

ing.

Setting the minimum navigation
volume

You can set the volume level at which
the navigation voice output is “mixed in”
with the audio source.

Note:

●

Set the volume on the navigation
system to maximum. If the output
sounds distorted, reduce the vol-
ume slightly on the navigation sys-
tem.

➮

Press the MENU button

8

.

➮

Press the softkey

4

assigned to

the “VOL” display item.

ADJUSTING THE VOLUME

«
...
12
13
14
15
16
...
»

Summary of Contents for Bremen CD72


















































Reviews:

No comments

Related manuals for Bremen CD72

Perfect Binder D1

Brand: Canon Pages: 99

Brand: Pyle Pages: 6

Brand: HAMTRONICS Pages: 11

MS4200RS - Navigation System With CD Player

Brand: Jensen Pages: 65

Radio Shack Realistic PRO-2021

Brand: Tandy Pages: 46

Brand: Farenheit Pages: 41

Brand: Alpine Pages: 71

Brand: DSC Pages: 5

Brand: RADICAL Pages: 13

Brand: Boss Audio Systems Pages: 17

Brand: Codex Pages: 8

Brand: Globalcom Pages: 24

Brand: Mpow Pages: 12

Brand: Jensen Pages: 2

Brand: Portech Pages: 8

Datacom TDT-100

Brand: Datacom Pages: 8

Brand: Forest Pages: 9

Brand: Sealey Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands