background image

4

www.blaubergventilatoren.de

KOMFORT EC SKE270-1.5

Fig. 1. Unit design and operating logic. 

DESIGN

The double-skinned unit casing is made of polymer-coated steel plates, 

internally heat- and sound insulated with a 15 mm polypropylene foam layer. 

The unit includes an integrated kitchen hood with control buttons on the 

front panel. The mounting brackets on the casing ensure easy installation. 

The spigots for connection to the air ducts are located at the side of the unit 

and are equipped with rubber seals for airtight connection to the air ducts. 

The front service panel of the casing ensures easy access to the unit internals 

for service works including cleaning, filter replacement, etc.

The unit is equipped with high-efficient external rotor EC motors and 

centrifugal impellers with forward curved blades. The integrated EC motors 

have the best power consumption to air capacity ratio and meet the latest 

demands concerning energy saving and high-efficient ventilation. EC motors 

are featured with high performance, low noise level and totally controllable 

speed range. The impellers are dynamically balanced. 

The unit is equipped with a high-efficient counter-flow polystyrene 

heat exchanger with a large surface area. The air flows are fully 

separated within the heat exchanger. Odour and contaminants 

contained in the extract air are not transferred to the supply air flow. 

The electronic frost protection system is used to prevent the heat 

exchanger freezing in cold seasons. In case of heat exchanger freezing 

danger communicated by the temperature sensor the supply fan is stopped 

to let warm extract air warm up the heat exchanger. After that the supply 

fan is turned on and the unit reverts to the normal operation mode. If air 

temperature in the intake air duct upstream of the heat exchanger is from 

-7 °C up to -15 °C the unit is switched into automatic control mode, i.e. 

the supply fan turns off for 5 minutes and operates for  25 minutes.  If the 

outdoor temperature is below -15 °C the supply fan turns off for 5 minutes 

and operates for  15 minutes. 

The drain pan under the heat recovery unit is used for condensate collection 

and drainage. 

The unit is equipped with an electric heater for operation during cold 

seasons at low outside temperature. The integrated electric heater is activated 

to warm up supply air up to +30 °C if set indoor air temperature may not be 

reached by means of heat recovery only. Once the set temperature is reached 

the electric heater turns automatically off. The electric heater is equipped 

with two integrated overheat protection thermostats, one of safety type 

actuated at +50 °C with automatic restart and the other one of alarm type 

actuated at +90 °C with manual restart. 

The built-in G4 pocket supply filter and G4 pocket extract filter provide 

efficient air filtration. Optionally, a F7 supply filter may be used. The kitchen 

hood has a multilayer fat aluminium filter.

The unit includes an integrated controller, a multifunctional control panel 

with LCD display and a remote controller. The delivery set includes a 10 m 

long cable for connection of the control panel to the unit.

OPERATING LOGIC

Clean cold air from outside flows to the heat exchanger, where from it is 

moved to the room with the supply fan.

Warm stale air is extracted from the room with the exhaust fan and is moved 

through the air ducts to the heat exchanger, where is transfers its heat energy 

to the intake air. After that it is exhausted outside. 

Heat energy of warm and humid extract air is transferred to the cold intake 

air. The air flows are fully separated within the heat exchanger. 

Heat recovery minimizes heat losses caused by traditional window 

ventilation and saves energy. 

In summer the heat exchanger performs reverse and 

transfers cold air from the cooled extract air for warming up intake air. 

This contributes to better performance of the air conditioner in ventilated 

premises.

During operation of the  kitchen hood the extract air is exhausted through 

the bypass air duct and does not come in contact with the heat exchanger.

SUPPLY FAN

HEAT EXCHANGER 

EXHAUST FAN

DRAIN PAN

SUPPLY FILTER

INTEGRATED CONTROL UNIT

HEAT EXCHANGER FREEZE 

PROTECTION TEMPERATURE SENSOR 

EXTRACT FILTER

ELECTRIC HEATER

KITCHEN HOOD DAMPER 

(AIR BYPASSING FROM THE KITCHEN 

HOOD) 

KITCHEN HOOD

min 1 m

SUPPLY AIR TEMPERATURE 

SENSOR

EX

TR

AC

T AIR

INT

AKE AIR

EXHA

UST AIR

SUPPL

Y AIR

KOMFORT_EC_SKE270_v2(4)_EN.indd   4

07.08.2015   14:25:41

Summary of Contents for KOMFORT EC SKE270-1.5





















Reviews: