background image

4

EN

Box Contents

• Blade 350 QX2 AP
• GB200 2-Axis Brushless Gimbal
• 3000mAh 3S 11.1V 20C Li-Po Battery
• 3S DC Li-Po Balancing Charger with 5A AC Power Supply
• Spektrum DX4 DSMX 4-Channel Transmitter
• 4 AA Batteries
• CGO1 1080p HD Camera
• Cell Phone Mount

Charging Warnings

The Battery Charger (EFLC3016) included with your quadcopter has been
designed to safely charge the Li-Po battery.

CAUTION:

 All instructions and warnings must be followed exactly. 

Mishandling of Li-Po batteries can result in a fi re, personal injury and/or 

property damage.

• By handling, charging or using the included Li-Po battery, you assume all risks 

associated with lithium batteries.

• If at any time the battery begins to balloon or swell, discontinue use imme-

diately. If charging or discharging, discontinue and disconnect. Continuing to 
use, charge or discharge a battery that is ballooning or swelling can result in 
fi re.

• Always store the battery at room temperature in a dry area for best results.
• Always transport or temporarily store the battery in a temperature range of 

40–120º F (5–49° C). Do not store battery or model in a car or direct sunlight. 
If stored in a hot car, the battery can be damaged or even catch fi re.

• Always charge batteries away from fl ammable materials.

• Always inspect the battery before charging.
• Always disconnect the battery after charging, and let the charger cool between 

charges.

• Always constantly monitor the temperature of the battery pack while charging.
• ONLY USE A CHARGER SPECIFICALLY DESIGNED TO CHARGE LI-PO BATTER-

IES. Failure to charge the battery with a compatible charger may cause a fi re 
resulting in personal injury and/or property damage.

• Never discharge Li-Po cells to below 3V under load.
• Never cover warning labels with hook and loop strips.
• Never leave charging batteries unattended.
• Never charge batteries outside recommended levels.
• Never charge damaged batteries.
• Never attempt to dismantle or alter the charger.
• Never allow minors to charge battery packs.
• Never charge batteries in extremely hot or cold places

(recommended between 40–120° F) or (5–49° C) or place in direct sunlight.

Low Voltage Cutoff  (LVC)

Low voltage cutoff (LVC) protects the Li-Po battery from over-discharge in fl ight 
and activates when the battery reaches a preset value. When the battery is 
discharged to the cutoff point, the aircraft will display rapidly fl ashing red, green 
and blue LEDs to warn you it’s time to land. When you see this LED code, land 
immediately to prevent over-discharge and damage to the battery.

When the LVC is activated, you have approximately 2 minutes until the battery is 
depleted and can no longer maintain a hover. Repeated fl ying to LVC will damage 
the battery.

NOTICE:

 Crash damage and battery damage are not covered under warranty. 

IMPORTANT: 

Always disconnect and remove the Li-Po battery from the aircraft 

after each fl ight. Charge your Li-Po battery to about half capacity before storage. 
During storage, make sure the battery charge does not fall below 3V per cell. 
A connected battery will result in trickle discharge.

Summary of Contents for Blade 350 QX2 AP Combo



















Reviews: