background image

12

EN

Preparing the 350 QX2 AP For Flight

CAUTION:

 When the home location is set (

step 6

), the 350 QX2 AP must be approximately 16 feet (5 meters) from where the pilot will stand during fl ight, 

pointing away from the pilot. If the aircraft is pointed in any other direction, the 

SAFE Circle

 feature will not function as expected and may result in personal 

injury or damage to property. Once the aircraft’s motors are started, do not change your position.

1.  Power on the transmitter with the fl ight mode set to 

Smart Mode 

and the throttle stick down.

2.  Install a charged battery, plug it in and close the hatch.
3.  With the quad on a level surface, turn on the power 

switch and allow the 350 QX2 AP to initialize.
If the GPS is enabled, wait for the GPS signal to be
acquired, which is indicated by a solid green LED. It 
may take from 30–90 seconds to acquire a GPS signal.

IMPORTANT:

 While in 

Smart Mode

 the motors will not 

start if a GPS signal has not been acquired.

4.  Move the aircraft to the desired home location and

orient the aircraft pointed away from the pilot.

5.  Step back approximately 16 feet (5 meters) from the 

home location.

6.  When you are prepared to fl y, you have two options to 

start the motors:

• Move the rudder stick full left, then full right, then 

back to center.

• Move both sticks into the bottom inside corners, 

then back to center.

7.  The props will begin to spin. The home position for GPS 

functions is set and your aircraft is ready to fl y. 

Lower the throttle stick and hold the bind button for
1 second to power off the props after fl ight.

16 feet (5 meters)

350 QX2 AP home location

Pilot location

SAFE Circle

Flying the 350 QX2 AP

Takeoff

Increase the throttle slightly above low stick (10–15%). 
The 350 QX2 AP altitude in 

Smart Mode

 corresponds 

to the throttle position. Low throttle is on the ground, 
slightly raising the throttle will produce a low hover, and 
the higher the throttle position, the higher the 350 QX2 
AP will ascend until it reaches its maximum altitude 
(approximately 45 meters).

Explore the fl ight envelope of the 350 QX2 AP in 

Smart Mode

 without fear of losing orientation. See 

the diagrams in the 

Flight Modes Explained

 section for 

more details on the aircraft’s function in 

Smart Mode.

 

In 

Smart Mode,

 the direction the aircraft is pointing 

does not affect the control, and the aircraft’s response 
relative to you (

the pilot location

) does not change with 

orientation. 

AP Mode

 and 

Stability Mode

 operate more 

like a conventional RC helicopter or multicopter.

Maximum altitude

(approximately 45 meters)

Intermediate altitude

On the ground

Full throttle

Half throttle

Low throttle

Mode 2 shown

Smart Mode Flying

Smart Mode Altitude Control

Front

LED

Summary of Contents for Blade 350 QX2 AP Combo



















Reviews: