background image

8

LED AND PARKING LIGHT INDICATIONS

STATUS INDICATOR (LED) FUNCTIONS

On Solid = Valet Mode
Slow Flash = System Armed
Rapid Flash = Passive Arming
Rapid Flash w/ Ignition on = Open Zone Warning 
Rapid Flash while Ignition on and Anti-Carjack

Mode Active = Entering Carjack Warning Stage

Double Flash = Auto Cold Start Mode Activated

PARKING LIGHT FUNCTIONS

On Solid = Vehicle Remote Starting
Flash I x = System armed
Flash 2x = System disarmed
Flash 4x = Defective zone warning (after arming)
Flash 4x = Tamper indication (after disarming) 

TRANSMITTER FUNCTION QUICK REFERENCE

TRANSMITTER OPERATION CHART

Operation

System Status

Ignition

1st Button 

2nd Button

Arm

Disarmed

Off

Button 1

Disarm

Armed

Off

Button 2

Remote Valet

Disarmed

Off

Button 1 Level Shift

Button 1

Remote Start

Either

Off

Button 2 Level Shift

Button 2

Auxiliary 1 

Either

Off

Button 3 Level Shift

Button 3

Toggle Chirp Mode

Either

Off

Button 4

*

Immobilizer

Disarmed

Off

Button 2 Level Shift

Button 1

Panic Mode

Either

Off

Buttons 1&2 together

Stop N Go 

Disarmed

On

Button 2 Level Shift

Button 2

Turbo Timer 

Disarmed

On

Button 2  

Manual Trans Mode

Disarmed

On

Button 2

Auto Cold Start

Disarmed

On

Button 2 Level Shift

Button 1

**

Car Locator

Either

Off

Button 3

Button 3

***

Shock Sensor Adjust

Disarmed

Off

Button 4 Level Shift

Button 4

Sensor Bypass (Main)

Armed

Off

Button 1

Button 1

****

Sensor Bypass (Opt)

Armed

Off

Button 4

Button 4

****

* If system is disarmed, Button 4 will arm system and change chirp mode (normal to silent or vice versa)

** Brake pedal must be pressed while performing button sequence

*** Must press button two times very quickly

**** Press multiple times to switch between normal, warning bypass, and full bypass

Level Shift: Pressing and holding a transmitter button for more than one second enters the Level

Shift mode for two seconds. The 1-way transmitter’s LED turns Green to indicate level shift,

while the optional 2-way transmitter plays a chime to indicate level shift. While in level shift

mode, pressing a transmitter button accesses the system’s special features such as Valet,Auxiliary,

etc. After two seconds, the transmitter will automatically exit level shift mode if no other

transmitter button has been pressed.

7250 rev 2 9-23.qxd  9/24/2004  12:54 PM  Page 8

Summary of Contents for BW X-Z

























Reviews: