background image

3

TAMPER ALERT

If the alarm was triggered while away from the

vehicle, the siren will chirp 3 times and the parking

lights will flash 4 times on disarming for tamper

indication. The triggered zone will be shown on the

optional 2-way LCD transmitter display.

AUTO REARM

If the system was armed for at least 10 seconds,

the Auto Rearm feature re-arms the system 30

seconds after disarming. The doors will also re-

lock if selected during installation. NOTE:

Opening the door resets the rearm timer, and

opening the trunk, hood, or turning on ignition

cancels the auto rearm feature.

The Auto Rearm

feature must be enabled during installation.

AUTO IMMOBILIZER

The Auto Immobilizer feature automatically

engages the starter defeat relay 30 seconds

after turning off the ignition. This feature

provides an extra level of security even when

when the alarm is not set. When immobilized,

the vehicle will not start with the key until

either transmitter button 2 is pressed, or the

override button is pressed with the ignition on.
NOTE: The auto immobilizer feature does not

operate while in the valet mode.
To turn the immobilizer on/off:

1. Press and hold button 2 for level shift.
2. Press button 3.

• The optional 2-way LCD transmitter

display will show “IMMOBILIZE”.

SILENT OPERATION MODE

Press transmitter button 4 to turn the arm and

disarm chirps on/off. NOTE: If the system is

disarmed, pressing button 4 to change the siren

status also arms the system. To disarm the

system, press button 2.
NOTE: The optional 2-way transmitter will still

beep to confirm systems arm/disarm.

IGNITION CONTROLLED LOCKS

The ignition controlled locks feature allows the

doors to automatically lock when the brake

pedal is pressed (after turning on the ignition

and closing all doors), and automatically unlock

when the ignition key is turned off. The ignition

controlled locking feature may also be

programmed for ignition lock without ignition

unlock, and off (no ignition control).
NOTE: If the optional remote start module is

not installed and ignition locking is desired, the

feature must be programmed for use without

brake. See Alarm Programmable Features.

REMOTE PANIC

In the event of an emergency (PANIC)

situation, the system’s siren can be triggered for

30 seconds to attract attention.
To activate the Panic Feature:
Press transmitter buttons I&2 for 3 seconds.

• The siren will sound.

• The parking lights will flash.

Press button I to exit panic mode and rearm

the system. Press button 2 to exit panic mode

and disarm the system. The Panic Feature will

NOT operate when the ignition is on.

EMERGENCY OVERRIDE

If the transmitter becomes lost or fails to

operate, the system can be disarmed by using

the emergency override feature.
To override the system:

1. Enter the vehicle.

• Because the system is armed, the siren

will sound.

2. Turn on the ignition key.
3. Press the Valet switch for 3 seconds.

• The siren will stop sounding.
• The starter defeat is deactivated.

7250 rev 2 9-23.qxd  9/24/2004  12:54 PM  Page 3

Summary of Contents for BW X-Z

























Reviews: