background image

4 — English

TRIMMER

  Inspect before use. Replace damaged parts. Make sure 

fasteners are in place and secure. Check for fuel leaks.

  Replace string head if cracked, chipped, or damaged 

in any way. Be sure the string head is properly installed 
and securely fastened. Failure to do so can cause serious 
injury.

  Make sure all guards, straps, deflectors, and handles are 

properly and securely attached.

  Use only  recommended or equivalent  replacement line in 

the cutting head. Do not use any other cutting attachment. 

To install any other type of replacement line or cutting 

head to this string trimmer can result in serious personal 

injury. Never use, for example, wire or wire-rope, which 
can break off and become a dangerous projectile.

  Never operate unit without the grass deflector in place 

and in good condition.

  Maintain a firm grip on both handles while trimming. Keep 

string head below waist level. Never cut with the string 
head located over 30 in. or more above the ground.

  This product is intended for infrequent use by homeown-

ers and other occasional users for such general applica-
tions as trimming light and heavy vegetation, etc. It is not 
intended for prolonged use. Prolonged periods of opera-
tion can cause circulatory problems in the user’s hands 
due to vibration. For such use, it may be appropriate to 
use a product having an anti-vibration feature.

EDGER

  Replace dull or worn blade; do not attempt to sharpen.

  Use this edger for edging along sidewalks, driveways, 

flower beds, and similar areas. Do not use for any other 
purpose.

  Be thoroughly familiar with the controls. Know how to 

stop the unit and disengage the controls quickly.

  Do not use the edger on or near graveled surfaces.

  Make yourself familiar with the area you are edging. Be 

aware of uneven sidewalks and holes in the terrain as well 
as other similar hazardous conditions (example: wire or 
wire rope which can break off and become a dangerous 
projectile). Always push the edger attachment slowly over 
rough ground.

  Do not attempt to remove cut material nor hold material 

to be cut when the motor is running or when the cutting 
blade is moving.

  Keep hands and feet away from the cutting area.

  Always keep your right hand on the rear handle and your 

left hand on the front handle when the blade is rotating.

 A coasting blade can cause injury while it continues to 

spin after the motor is stopped or throttle trigger released. 
Maintain proper control until the blade has completely 
stopped rotating.

 Check blade nut for tightness before operating the 

attachment.

  Improper assembly can create a dangerous situation.

  Never stand or have any part of your body in line with the 

path of the edger blade.

  If the edger strikes any type of foreign object:

  a) Stop the edger and remove the spark plug wire or 

disconnect from the power supply.

  b)  Inspect for damage to the edger attachment.
  c)  Correct damage before using the edger attachment. 

Failure to do so can cause serious injury.

  Always stop the engine or motor and remove the spark plug 

wire or disconnect from the power supply before attempt-
ing to remove any obstruction caught or jammed in the 
blade, installing attachment, or making any adjustments.

  Save these instructions. Refer to them frequently and use 

them to instruct others who may use this product. If you 
loan someone this product, loan them these instructions 
also to prevent misuse of the product and possible injury.

  Allow the engine to cool; empty the fuel tank into a con-

tainer approved for gasoline and secure the unit from 
moving before transporting in a vehicle.

  Wear your protective equipment and observe all safety 

instructions. Be sure the cutting attachment stops turning 
when the engine idles. When the unit is turned off make 
sure the cutting attachment has stopped before the unit 
is set down. 

  We recommend taking your equipment to a qualified 

service center for repair, as service performed by 
inexperienced or unqualified persons may damage the 
equipment, create unsafe conditions, injury to user and/
or void your warranty.

GENERAL SAFETY RULES

SPECIFIC SAFETY RULES

Summary of Contents for BM25TEC





































Reviews: