background image

15 — English

TROUBLESHOOTING

 

PROBLEM  

POSSIBLE CAUSE  

SOLUTION

1.  Clean or replace spark plug. Reset spark plug gap. 

Refer to 

Spark Plug Replacement earlier in this 

manual.

2.  Push primer bulb until bulb is full of fuel. If bulb does 

not fill, primary fuel delivery system is blocked. 

Contact a qualified service center. If primer bulb 

fills, engine may be flooded, proceed to next item.

3.  Set the choke lever to the 

FULL CHOKE position. 

Squeeze the trigger and pull the starter grip and 

rope repeatedly until the engine starts and runs. 

 

NOTE: Depending on the severity of the flooding, 

this may require numerous pulls of the starter grip 

and rope.

1.  Use fresh fuel and the correct 2-cycle lubricant mix. 

(50:1).

2.  Clean air filter screen. Refer to 

Cleaning Air Filter 

earlier in this manual.

3.  Contact a qualified service center.

4.  Clean or replace spark plug. Reset spark plug gap. 

Refer to 

Spark Plug Replacement earlier in this 

manual.

1.  Turn idle speed screw clockwise to increase idle 

speed. 

See Figure 16.

1.  Lubricate line with silicone spray.

2.  Install more line. Refer to the applicable line 

replacement section in this manual.

3.  Pull lines while alternately pressing down on and 

releasing spool retainer.

4.  Remove line from spool and rewind. Refer to the 

applicable line replacement section in this manual.

5.  Advance line at full throttle.

Engine will not start

Engine does not reach full 

speed and emits excessive 

smoke

Engine starts, runs, and 

accelerates but will not idle

Line will not advance

1.  No spark.

2.  No fuel.

3.  Engine is flooded.

1.  Incorrect lubricant/fuel mixture.

2.  Air filter is dirty.

3.  Spark arrestor screen is dirty.

4.  Spark plug fouled.

1. Idle speed screw on carburetor 

needs adjustment.

1.  Line is welded to itself.

2.  Not enough line on spool.

3.  Line is worn too short.

4.  Line is tangled on spool.

5.  Engine speed is too slow.

1.  Clean threads and lubricate with grease - if no 

improvement, replace the spool retainer.

1.  Cut tall grass from the top down to prevent 

wrapping. 

2.  Operate trimmer at full throttle.

1. Reassemble shafts. Refer to 

Joining the Power 

Head to the Trimmer or Edger Attachment in 

the 

Assembly

 section of this manual.

Spool retainer hard to turn

Grass wraps around drive 

shaft housing and string head

Engine starts and runs but 

string head does not turn

1.  Screw threads are dirty or damaged.

1.  Cutting tall grass at ground level.

2.  Operating trimmer at part throttle.

1. Shafts are incorrectly assembled.

If problem persists after trying the above solutions, contact customer service or a qualified service center for assistance.

NOTICE:

As the equipment owner, you are responsible for the performance of the required maintenance listed in the 

Maintenance

 

section. It is recommended that you retain all receipts covering maintenance on your equipment. Neglecting or failing to 
perform the required maintenance may increase emissions, decrease fuel efficiency, degrade performance, cause irrevers-
ible engine damage and/or void your warranty.

Summary of Contents for BM25TEC





































Reviews: